HiLetgo 5pcs L9110S DC Motor Drive Module Stepper Motor Drive Controller Board 2.5-12V H-Bridge Can Drive Dual DC Motor at The Same time or 4 Wire 2 Phase Stepper Motor

The dual H - bridges arrived on time and were well packaged. I have a 74194 universal shift register to drive the 4 inputs to the dual H - bridges.In my case I used a 555 timer to generate a clock pulse of 1 Hz to control the 74194. The 4 output pins to the shift register were carefully connected to the dual H - bridge connection terminal block. You have to study your 4 wire connections to the terminal block to get the pulse sequence correct. But, I had done this. Make sure you ground your dual bridge to the 74194 bread board and use two D dry cells to apply 3 volts or so to the dual H - bridge circuits. My NEMA 17 stepper motor worked great with this design and it was great to know that the dual H - bridge circuit boards were well made, well designed and were reliable. I used 4 AA bateries (6 volts) to power my shift register.

Here is a sort of DIY datasheet: http://me.web2.ncut.edu.tw/ezfiles/39/1039/img/617/L9110_2_CHANNEL_MOTOR_DRIVER.pdfFor more info just search on l9110 motor drivers. I gave them PWM at 10k and they took it but started getting pretty hot when I stepped up from there. I was trying to avoid audio issues and it's best to stay above 20khz but that didn't work out.Here's a bit more on it:The HG7881 (L9110) is a compact motor driver chip that supports a voltage range from 2.5-12V at 800mA of continuous current. These chips have built-in output clamp diodes.Each HG7881 (L9110) chip is able to drive a single DC motor using two digital control inputs. One input is used to select the motor direction while the other is used to control the motor speed. Speed is controlled by using PWM Pulse Width Modulation. Motor drivers typically have what is called a truth table that determines the effect of its inputs. The truth table for a single HG7881 (L9110) chip is as follows:HG7881 (L9110) Truth TableInput OutputIA IB OA IB DescriptionL L L L OffH L H L ForwardL H L H ReverseH H H H OffNote that the actual direction of "forward" and "reverse" depends on how the motors are mounted and wired. You can always change the direction of a motor by reversing its wiring.The HG7881 (L9110) Dual Channel Motor Driver Module uses two of these motor driver chips. Each driver chip is intended to drive one motor, so having two means that this module can control two motors independently. Each motor channel uses the same truth table as above. Each set of screw terminals is used to connect a motor. Refer to the table below for pin header connections.HG7881 (L9110) Dual Channel Motor Driver Module ConnectorPin DescriptionB-IA Motor B Input A (IA)B-IB Motor B Input B (IB)GND GroundVCC Operating Voltage 2.5-12VA-IA Motor A Input A (IA)A-IB Motor A Input B (IB)Recommended using input 1A to control the speed of each motor and input 1B to control the direction.

I ordered these to drive a 12V DC motor that draws around 100 mA. Pop! No more motor controller. Tried it with and without the 1k pull-up resistors soldered to the board. Same outcome. Most I'd use these for is 6V. Seller should include a circuit diagram of the breakout board as well as the controller itself.

Easy to get up and running with Arduino, plenty of documentation on how to use. Easy to use and they work. Just follow instructions and the item works as intended.

Works as it’s supposed to.

If you don't know what Ohm's law is, get something else. That said...Briefly, these are perfect for 5v, and up to 500mA of current. Unfortunately, there's no current protection on the outputs, but by using a 10 ohm 1/4watt resistor on each output phase, you will not burn these up, even if you accidentally short the outputs *after* the resistors.

Super low cost, so that's great. Being a typical product from SZ, it will be fine AFTER you fix it.Each of the 4 logic inputs are pulled up to the 12V input, that's rude (and might damage) the processor. that run on 3.3 volts and could damage them. just remove the 4ea 10K resistors and you will be fine. Also the red power LED is nice but has a 1K resistor, It is waaay too bright. Replace the 1 K resistor with one of the 10K's that you removed from the inputs for a more reasonable brightness for a power led. If you want to use PWM remove the capacitor that is across each of the outputs. PWM can't drive a capacitor. Better yet reuse the capacitor and add a series resistor like 68ohms in series with it. Google "snubber circuit"

I received a set of 5 that were individually wrapped all in one bag and many of the control pins were bent as there's no protection in the package; there's no foam padding or anything on the pins and at some point the packages had all stabbed each other and every board had at least 1 bent pin. Removal from the packaging was difficult due to the pins piercing the static bags and being bent.Still a decent value but be aware that you may need to replace at least some of the of the pins.

I am using these to run LEGO motors via Arduino at 9 to 10 volts. The 1508 motor drivers kept dying on me.

Brilliant pair of H-bridges for arduino dc motor drive. Work perfectly and arrived in good time.