Best Tek Garmin Edge Extended Out-Front Mount, Bike Handlebar Mount for NiteRider Adapter, Sports Action Camera,Garmin Edge 25 130 200 500 510 520 800 810 820 1000 1030

I like this, it allows me to use garmin device and also either go pro or light.

** it seems that Amazon may have already stopped selling the inferior model I originally purchased and that this review is about, it came with a Wahoo mount and an elastic band mount for generic lights. This item is the BestTek one I bought second time around and I'd recommend, be wary though as to which one you order.**This is a terrible product. Please spend the extra £4 and buy one of the others like the Best Tek one. The images look the same but please be assured the products are worlds apart.I can forgive the rough casting of the main aluminium bracket, I can also overcome the fact that the GoPro mount is to widely spaced so that when you tighten the bolts the plates don't clamp the camera tight so it flops around, apply an extra bit of torque to the bolt and it strips the thread and just spins, this can be over come with a nut, but even then you have to pack between the fins with washers to clamp it tight.I can also get over the fact that the Garmin mount is extremely tight and difficult to turn the computer in, so much so the bracket flexes and it all feels like it's going to break, but what do you expect for £6.50?The main dangerous aspect of this mount, is the fact that the spacer tubes that slide over the long replacement stem face plate bolts are soft plastic. Most stems require you to tighten all 4 face plate bolts evenly to 4 or 5Nm. It is impossible to achieve this torque as approx 3Nm of torque starts to crush the spacers and pull them into the bracket. I actually tightened then as much as I could took it for a test ride and the bars dropped and spun as I rode because the bars can not be clamped tight enough.It is impossible to safely install this bracket with the supplied spacers as the required torque is too much for the plastic. The Best Tek mount comes with aluminium tube spacers and took the required torque with no trouble.I would actually call on Amazon to withdraw this version from sale.

Bought this to hold my Garmin and allow my GoPro to be visible to all the cars that pull out on me.Fits easily, replacing your bolts.Garmin locks in secure, not fallen out yet and I hop the bike a lot.GoPro bolt is very tight, takes a lot of screwing in and is a little close to the mount, so can be hard to release with gloves on. Hence 4*, but maybe a decent feature to stop it being easily pilfered

I bought this to fit on my MTB to mount a Garmin Edge 530. The mount is made of aluminium and very sturdy but lightweight. My Garmin fits very well and feels very secure when mounted. The downside of using this type of mount is the position is fixed so you cannot alter the viewing angle in which case an arm type mount may be preferable as you can change the viewing angle. My only criticism is the fitting instructions which are a bit basic. The fitting screws to the handlebar stem have two small black sleeves that crushed when I tightened them. I'm not sure if they're supposed to but the mount and handlebars are certainly secure. There is the facility to add a camera to the underneath of the mount but I have no requirement to do this.

Came recommended and came with metal and not plastic spacers. So far so good although once all put together discovered that the cap head screws are 4mm and therefore too small for my stem which has 7mm fixings. Also, wouldn’t be able to fit those through the space at the front of the mount without having to faff about with a file etc. Not worth the hassle.

This does the job well, I always had sram out front mounts before but I've now got these stem direct mount units now from "best tek" and they are fine. Made from aluminium rather than the plastic sram ones but it looks a lot more tidy to have mount in-line with stem compared to sitting offset from the bar mount.One word of warning though if you have carbon bars then you definitely need a torque wrench (5Nm max bolt torque) to ensure no damage to bars, and the bolts that the mount connects to are very close under mount, so you will need a long legged torque wrench to get to bolts.

Terrible quality product not fit for purpose. The plastic material used is not strong enough to handle the recommended stem face plate bolt torque settings (5NM) to enable safe installation and operation of handlebars and stem. The mounting spacers have become mangled and the mount itself snapped well before reaching 5NM torque. Aweful.

The stem mount itself (metal) seems pretty solid (although slightly bent to one side - poor manufacturing), but the Garmin adaptor (plastic) snapped only after a few hours of riding, and my Garmin unit flew off while riding. Had I not secured it with the strap too (for safety), it would have hit the tarmac at speed. Beware. The adaptors included seem to be made by cheap plastic that breaks easily.

This out front mount is great! Easy to install. Really solid mount, and it looks sleek. The retention on the Garmin is really good, and I like the option to mount a light or GoPro on the bottom. You can't adjust the angle of the Garmin, but this hasn't been a problem for me.

Excellent produit, facile d’installation et robuste.

Produit de qualité et pratiqueFait le job

Die Panmout Extended Out-Front-Halterung ist trotz ihres günstigen Preises aus China sehr empfehlenswert. Sie sieht gut aus, ist stabil und lässt sich leicht montieren. Für den Preis bietet eine überraschend gute Qualität. Definitiv eine gute Wahl für jeden, der eine preiswerte und zuverlässige Halterung sucht.

Prodotto in alluminio, stabile e abbastanza robusto, perfetto per utilizzo su strada e con supporti tablet da manubrio per allenamenti indoor.Soddisfatto