PEMENOLTWS Bluetooth Mono Amplifier Module 100W DC 7-24V with TPA3116D2 Chip, Wireless Stereo Pairing, Multi-Input USB AUX Bluetooth, Volume Knob Control for DIY Car & Home Audio

Could be in a more esthetic looking box but that's only because its in our living room other than that this little thing puts out loud, clear sound. I have it pushing just one 8" skar marine speaker and that thing screams. The bt is easy and quick to pair with a good range, I can go from where it is into the master bedroom, close the door, and into the bathroom, and close that door going through 2-3 walls and the washer and dryer and still be connected. Great clarity, no distortion, PLENTY of power. Highly recommend for a budget Bluetooth speaker build.

This PEMENOL TWS amplifier board is a stellar find—crisp Bluetooth, AUX, and USB audio, all in a neat metal box. Delivers solid 100W output from a 7–24V input, making it perfect for car, home, or DIY speaker builds. Setup was easy, TWS pairing worked flawlessly, and the sound quality impressed. Great upgrade for anyone building their own audio gear!

Great little amp for a DIY bluetooth speaker. Pretty simple assembly, and mounting. My only ding is that its rated for 100W, if you go with a 150-160W speaker at full volume you'll get a little distortion. Might need to go with a 200W instead.

Very good Class D Amplifier for this priceThis is class D amplifier (sometimes it is called “digital” amplifier.The advantage of class D is very high efficiency >90%.The disadvantage is higher distortions, but in most applications, it wouldn’t matter, and people wouldn’t hear it.I powered the amplifier from the bench Power Supply and tested it at different voltages, measuring the input power (Pin, W) and the output power (Pout, W) at 4 Ohm load, using sinewave generator at my phone over Bluetooth, as the input signal.Two Oscilloscope channels were connected to two output terminals (this is a “bridge” amplifier and load is connected between two active outputs). The output peak-to-peak voltage (Vp-p) was measured.The output power was calculated Pout = ((Vp-p) * 0.7)^2 / 4.Volume was adjusted to provide maximum output amplitude without clipping.Results (1kHz, 4 Ohm):Vin = 12V, Iin = 1.3A, Pin = 15.6W, Pout = (11.0*0.7)^2 / 4 = 14.8W, Efficiency = Pout / Pin * 100% = 95%Vin = 16V, Iin = 1.6A, Pin = 25.6W, Pout = (14.0*0.7)^2 / 4 = 24W , Eff = 94%Vin = 20V, Iin = 1.95A, Pin = 39W, Pout = (17.0*0.7)^2 / 4 = 35.4W, Eff = 91%Vin = 24V, Iin = 2.25A, Pin = 54W, Pout = (19.8*0.7)^2 / 4 = 48W, Eff = 89%• Note: The Amplifier output was shutting down after 10 seconds and coming back in a few seconds as a result of over-temperature protection., because the Test was conducted with the continues sinewave and the amplifier is not designed for this condition. Normal audio signal has significantly lower average power.Result (1kHz, 3 Ohm):Vin = 24V, Iin = 2.98A, Pin = 71.5W, Pout = (19.6*0.7)^2 / 3 = 62.7W, Eff = 88%• Note: Over-temperature protection was shutting down the output after 1 second and coming back in a few seconds.•Frequency Response:20Hz – 18kHz• Note: My Generator lowest frequency is 20Hz and I couldn’t test it below.• There is no output signal above 18kHz.What I like:Small sizeQualityEfficiencyBT and analog inputWhat can be improved:The heatsink is attached with double-sided tape, which is not very secure and doesn’t provide good heat transfer.Conclusion:Very good class D amplifier for the money

Although it doesn't come with the instructions on how to connect two together (TWS Mode), I found what I believe is that resolve.Connect One amp to a bluetooth source (phone, mp3 player, etc), and leave the other disconnected from said bluetooth source. Click the potentiometer (volume knob) three times on the amp that is connected to the source. Then click the second/other (disconnected) potentiometer three times. Both amps should show a rapid flashing blue/red light indicating they have activated 'pairing mode'. In 1-5 seconds you should hear an audio sound from both amps/speakers. The flashing lights will then show synchronized slow flashing.Note: Although they are now in 'tws mode' volumes are still individually maintained.I have purchased a total of 19 of these amps over the course of 2 years (used in bluetooth speaker boxes). Every Single One is still in perfect working order. When using the correct power and speakers, these things are monsters of sound. I highly recommend.Buy one or two, and make up your own mind.

Very coolks

Endless loop of beeps trying to connect and fail to connect. Still using as they are simple amps and sound great, they do the job if you do not care about linking two together

these little beasts really do the job. I have used a number of the to build Blue Tooth speakers and they work very well and pair quickly.