DROKDC Boost Converter 900W, 8-60V to 10-120V 15A Step Up Converter Adjustable Voltage Regulator Output 48V 24V 12V Power Supply with LED Display Cooling Fan

Have tried a bunch of different DC to DC converters and this is the only one that even comes close to delivering rated specs. Fairly easy setup, and can be configured to enable output automatically at powerup. I'm using it to charge a LiFe battery from my main car battery on a switched source. My input voltage can drop as low as 10V under load (due to a long wire run) and I've got the output set to 14.4V and the battery pulls it down to mid 13's when it's charging. This board will deliver about 12A pretty reliably so about 160W.Some of the other DC to DC boost converters I've tried either won't power on at all, or switch off when the input voltage drops, or just won't give me more than 8-10A (while often being rated for 15-20A). This one just works.The only issue I have is that it has no case, and all the electronics are really out there on both sides of the board, so be careful you don't short it out on something.

When shopping for a 120VDC voltage booster, I considered another product. Amazon had noted that it was returned very frequently, so to be careful with the order. In the comments, someone noted that it had a positive ground common to both input and output. This would be a no-go for my application, and probably for most applications. So I kept looking.The listing for THIS booster circuit didn't specify positive or negative ground, but the manual seemed to imply a negative ground. Indeed it is a negative ground, common to both input and output. (It can be wired with three wires if desired.)The board was easy to install, and it operates rather intuitively. It can be programmed to put out a predetermined voltage when powered up (without requiring any buttons be pressed). Or it can be programmed to produce that voltage only when a button is pressed. When it is not producing the programmed voltage, it puts out a fraction of a volt less than the input voltage. (I didn't test whether this voltage could be killed with a small resistive load.)I powered my board with 12VDC and boosted to 120VDC. When powering up, it takes a few seconds for the capacitors to charge and for the output to ramp up to 120VDC. The output is steady and smooth, and the voltage is accurate.I can't attest to how well the board performs under a heavier load. I'm only drawing about 25 mA from the board! Others have suggested that the board whines under load, However, with my light current draw, I have heard no whining.

I have to say this is a quality product even though it's really frustrating that it doesn't come with a box. I'm going to tell you how to fix that. Just buy one of those little plastic trays from the Dollar tree. The one that's too small for pencils or anything but little change things. It fits right over this thing so take a small anything flat that isn't conductive and glue it to it and then put that box over it. Take scissors and cut a flap where the input wires go and one where the output wires go and you're set as far as protecting it and then you can just lift that cover off and put it on as needed. Now as to not being smart enough for my laptop. First of all I have to say you have to set both the voltage and The max amperage to what they are supposed to be just what is on your existing adapter. The computer has a charging circuit inside and it's really quite sophisticated. There are essentially two computers working. One is a main integrated controller and then there's the charging subsystem and it's possible for a manufacturer to build into the power adapter, some kind of resistance value or other source of verification that that is indeed the original power adapter which I think my laptop has that. If that's true, then there's no way that you can use one of these buck boost converters without hiring an engineer to change that resistance value . So The rest of the story goes that I did not originally set the max amperage because the boost converter itself is only capable of a total of. I think it's 15 amps and the adapters is 11.7 amps but will only take what it wants. Well that's not a good idea because what happened Was it basically scrambled Something inside that very complicated circuitry and the computer no longer would charge or run from the power adapter. It would only recognize the battery and it was using the battery power only. That was not something that I needed at that moment for sure because I'm mobile in between homes and in between cities. So losing your laptop is not good timing. This all has to do with mobile power for me to get by. And ultimately, the best solution is to use an inverter with your existing power brick. Just don't spend a lot of money on an expensive inverter that you're probably going to want to replace. Just get a simple pure sine wave inverter. Maybe as little as 500 W but you can probably get 1,000 or 1,500 W for the same price. I'm not here to give you that advice actually. So having just spent over $1,000 to move my stuff into storage I am broke and so I have to return this thing just to get an inverter to replace it. I may try resetting my subsystem again and the way you do this is Basically there's either a a button. Excuse me, a hole in the base of the computer usually to press or you have to disconnect the battery and then hold the power button for 30 seconds and then reconnect the battery. So that worked to restore my laptop. Thank goddess. But I have no better use of my laptop than what I started out with a couple of weeks and $300 ago. I'm forced to use my PayPal credit on eBay or possibly home Depot but I need it now so thanks again. Amazon prime for your return policies.Last update so I had a really inexpensive inverter 700 W that I got from harbor freight a long time ago. I don't know years ago that turned out to be a modified sine wave. You have to look in the details doesn't say and that's plenty. Good enough to run these adapters. There's a lot of fear about it, putting interference or destroying things in your computer and all that. Oh, I wouldn't run a computer directly, but it's not being run directly. It's being run through a very sophisticated adapter that's designed to take all kinds of different waves or waveforms so that's the first thing. The second thing is that you don't necessarily have to run the computer while you're charging, so at least as an experiment because I'm a cautious fellow- the first thing I did was charge my computer while it was off technically hibernating. And it worked that cannot harm your computer and it's not going to harm your adapter. So there you are. You have like a $30 or $10 at a swap meet inverter to run your laptop in your car. However, do get a storage battery and a charger. That's where the other $300 came from.

Tried using this to bump a 12v 18a power supply to 24v 6.25a. Well within the advertised specs of this converter. It wouldn't even go past 4 amps. And everytime it got to 4 amps, it would make a high pitched whine and glitch back down to 2 amps then slowly build back up to glitch again. Thinking it was too big of a power draw (*which it most definitely shouldn't have been. I tried hooking up a 2, 10w leds in series that needed 24 volts at 1 amp. It flickered ferociously and would not even get to half an amp then spike to 1.5 amps, and the voltage danced around between 18-24v.I have no clue what the issue might be... but I HIGHLY down this thing could even handle half the load as advertised. Let alone, efficiently and/or safely. Stay away from.