Nilight Headlight Assembly for 1999 2000 2001 2002 Chevy Silverado 1500 1500HD 2500 2500HD 3500 Chevrolet Tahoe Suburban Replacement Headlamp Housing Bumper Lights Set

Very quality headlight they look fantastic on my 01 Chevy Ease of installation:Very easy to install no tools required

These fit very nice, easy to install, lenses are very clear and bright.

Bought this item in Jan and installed and adjusted lights no problems at all. They are bright and clear are a vast improvement the original 02 2500 headlight assemblys. In April the driverside daytime runnig light popped out of place, no big deal put it back a week later it did it again, then a fed days later. When i reinstalled it each time the clip would click and it would not move when i pulled to make sure it was locked in place. It kept dooing it so i messaged this seller, no response bit it was ober the 30day return ect so I went to nilight.com it stated has a 2 yr warranty so I sent a email. No response for a week called the number on the web site during business hours said to send text will have a response in 15 business hours. Had no response again. Sent another email amd text with the information they requested. Nothingit is now end of June and the locking clip is broke. I have sent several more text and email with no responses. They are bright and clear but if you have an issue your on your own and apparently the warranty is just a sales gimmick.

These headlight assemblies are very clear and bright. They were a little tricky getting in place, but with some fanagling I finally got them seated so I could slide in the holding rods. One of the adjuster blocks broke and I got a replacement. The common complaint with these assemblies is the lateral and elevation adjustments don’t work or break, and that was the case with my first set. All the brands seem to have this issue. So here’s my work around in the second set: I used super glue (jb weld would be better) on the adjustment screw anchor point and beefed up the plastic mounting point. The adjustment screw is very rough and poorly machined, and that contributed to the first adjusters breaking. So I used silicone oil on the screws, and dripped some into the jackscrew block mechanism. I also marked the direction for each adjusting nut so as to avoid any unnecessary turns. And lastly, I was very gentle adjusting the elevation and lateral movements. It all seemed to work out. I’m probably like a lot of you and resent having to do diy on new products, but the alternative to these $85 lights are OEM at $400-nuff said!

Arrived this morning and installed this morning. 2003 Chevy Tahoe. Easy install, takes about 20 minutes total to remove the old and install the new. Crystal clear, very bright with my Sylvania ZXE Gold bulbs, beautiful transformation, really improves the look of my truck, perfect fitment, no gaps anywhere, tight fit. I would definitely recommend these light assemblies to anyone needing some great lights and if ever needed I would definitely buy them again. Tips: Before installation, adjust the up/down screws in until they are about 1/2 an inch long, they are set too far back from the factory and will make it seem as though they aren't going to fit. Disconnect your bulbs and place the bulbs in the assembly then, connect your harness back up, the low beam bulb fitment is very tight and will be hard to connect with the harness on. Be sure to check daytime running and signal assembly and make sure you have the correct lights for the side that you are getting ready to put on, they will fit bavkwards but you'll notice it's really tight and will have a bad gap (Ask me how I know😂) Overall I am 200% satisfied with this purchase. The fog lights were purchased 2 years ago from Topscope, they still look great and perform great.

The media could not be loaded. Style yes looks great and as a whole assembly yes its the right assembly. BUT, the socket hold downs were not correct. All the ratings about condensation is because the lower lights are not oem thickness at all the socket holes, one in particular can't remember which one maybe side marker is too thin to hold down the bulb socket/connector tight. The main thing was the headlights, the hold down was not correct, OE bulbs were loose, I had to shave the screw towers for a proper fit. installing LED bulbs HIGH and Low, oddly enough the Low beams were pretty good, i think i shaved one of the 2 for tightness. Both L/R Highbeams for LED's were not correct i had to shave both sides for fit and had to rotate the hold down for it it to be correct LED alignment. I purchased amazon LED's, so that was an initial factor but I did put them in my old assembly and they fit perfect and aligned straight. (LED's (especially headlights) are very specific when being aligned. up/down like the initial would have been worthless, side to side to match the headlights reflection surfaces is ideal...and was achieved. kinda id say 95%, with fabrication. There is a lock point but no matter how I could change the hold down orientation it did not create perfect alignment. Had to on both sides rotate back from lock position maybe 10 to 5 degrees from lock to be perfect.) SO good fit for your body, great style, but terrible connector fit, I've gotten it to work but it made a 30 min change a 3 hr retrofit for it to be perfect. Great deal and no telling if others will be any better to the points I found, but for sure these needs some help to be perfect especially with LED's. Not so much an issue with halogen but the tightness would be a concern for sure.i've added a a video sorry for the shakiness 2 hands and 3 objects lol, thought i had taken photos to show the alignment issues, but essentially it would have should the 2 sided LED's pointed up and down towards no reflective surfaces while side to side is the way to go so the light actually hit mirrors. ***To be clear my stock assemblies allowed that perfect alignment and were tight with each LED. So I would not say exact fit or complete ease of installation if you are expecting it to be 100% correct. The lack of tightness is for sure a concern for the longevity of your halogen bulbs.

👎🏽DOES NOT FIT THE 2001 CHEVROLET TAHOE THE CLIPS ON THE TURN SIGNAL LIGHTS DO NOT CLIP IN PROPERLY.👎🏽