GOOFIT PD24J Carburetor 24mm Carb for 4 Stroke GY6 125cc 150cc ATV Go Karts Motorcycle Scooter Mopeds 152QMJ 157QMJ Engine

This carburetor works absolutely flawlessly. Perfect fit and everything plugs up the way it's supposed to. It is an exact replica of what I had on my bike to begin with and does exactly what it's supposed to be doing. Very easy to install very good quality.

I have been trying to figure out these carb’s setting for yrs now. I always get it wrong. I recently bought a new bike n didn’t touch that carb n it’s been working like a champ doing 53 miles a day for 4 months n counting. Then I know my old bike needs one of those perfect setting carbs where I wouldn’t have to mess with it. I have tried changing the jets, I got it too tight which makes the engine too lean like it’s on high idle. That was 100 x 35. I have tried using glixal 26mm carb, but I did mess with the air n the idle screw. I have tried using glixal 24mm carb, again I mess with the air n the idle screw. This time I try using Goofit’s carb 24 mm without using anything I learn from YouTube n it works like the new bike. Smooth throttle response, great idle, and a button press at startup.I’ve made this my goal for both bikes to rebuy this specific goofit carb n just install it in there should any of the carbs went bad in the future. U have no idea how frustrating it is when ur trying everything u c online, come to find out none of them works...

Product fit and worked fine. My only complaint would be that the screws were too soft.I took the electric choke off and put the original manual choke on it. While doing this I stripped 2 of the screws.After getting the screws out, I installed the unit on my mothers (Menard's special) Yardsport YS200 and it started right upand ran fine. It didn't even need any adjustment.

Installed it easily, just had to loosen the air filter box. Cranked up and idled perfectly without any adjustments.Has actual screws on the float bowl and top diaphragm. For $30 can't beat it.Bought it again Oct 2022. Made the same mistake using Ethanol gas and letting it set too long last year. This new one works great, no adjustment was needed. No more ethanol gas for this and the mowers.

Muy buenos

I have a 2020 Amigo scooter that I have had for 7 months. I went out to start it and it would briefly start and then quit. I removed the auto choke and taped the hole. The engine started right up. I then replaced the choke and it still would not start. I purchased this carb that fit right in with no mods. Engine started right up and runs better than with the old carb when it was operating correctly. A six month old new scooter should not have the carb stop operating........A new factory carb was 80 dollars which was ridiculous. Time will tell if this will last. I will update at six months.

I bought this carb mainly because it was cheaper than buying all the parts to rebuild the original. That said, my expectations were not all that high despite the overwhelmingly high reviews it has. I also picked this one because it says in the description of what it fits that it will fit my daughters Buddy 125. That's where the three star review comes in. The carb itself is too long front to back, too tall, and the throttle cable bracket/setup is too widely spaced and the throttle cable bolt is too big for the bracket. I reversed the bracket and finely tuned it with a large hammer until I got the spacing I needed, drilled out the bracket and viola, throttle cable is hooked up. Cut back the front manifold and reamed it out to gain 3/8" and with a box cutter and a propane torch manipulated the air intake manifold and kind of forced it in place. It sits at an angle now, but it is sealed up and works. Had to make a longer tube that goes between the manifolds, threw out the fuel filter and replaced the fuel line.Lastly I had to make a spacer for the access lid inside the storage well under the seat to clear the top of the carb when the seat assembly is installed. I would like to know what that stylish wrap around the carb twice vacuum line is for. I am guessing it is vital to some other vehicle, not our Buddy 125. On the plus side, once installed, the scooter really scoots along! (Sorry) It seems to be working just fine without any adjustments to the idle or mixture screws. Time will tell how long it will last, and if it goes wonky on me, I will buy another one. Yes I feel it only deserves three stars because of the fit, but really, a working carburetor for less than $30? AS long as you have a smidgen of mechanical ability you can't go too wrong with this one.

Well packaged, throttle Vacuum & fuel inlet Nipple and butterfly opening were covered to prevent dirt and damage,First engine start was easy and smooth, no adjustment was needed before test drive, its been 3 days less than 20 miles and still no adjustments to it, after 100 miles i will look at the sparkplug and make adjustments, this is my run around and do errands vehicle, not a racing machine weighs 290# , 2008 ZN150-T24 Rebel/Rowdy/RoverCruising Scooter (different names same scoot) bought used from the first owner in 2011, I've been riding this scooter for 12 yrs