OPT7Aura Aluminum Car Underglow Lights with Remote Control, Exterior Neon Accent Under Glow Kit for Cars, Waterproof Rigid Light Bars, Music Soundsync Lighting, RGB Multicolor LED Strip, 12V Decor

The lights are bright and very well priced. They are easy to install too. They are great quality!

Overview:Pros->Great build quality>Easy installation (but can be time consuming)>Very bright at night>Easy to control (using both the main remote control and key fob)>Uses barely any battery>Will work on almost any carCons->Connectors are flimsy (the metal prongs inside)>Cables aren't long enough for longer cars>Key fob controller has a short range>Is barely visible during daytime (which really is no problem)>I had mounting issues on my vehicle on the sides (results may vary for your vehicle)In depth review:I had been looking at tens of different underglow kits on amazon, and across the Web. Most scared me with their cheap prices (some costing only $30!) and others just did not have any good reviews at all. I came across this Opt7 kit about a month ago and instantly could tell that this was no ordinary kit. This one seemed to have much higher reviews, and much better advertising than any other sub $100 kit. So I purchased it, planning on doing the full installation myself. First I tested it with the 12v outlet to make sure that all of the strips and cables worked, which they did and the brightness sitting on the roof of the car during broad daylight surprised me (however once they are under the car it is a different story during the day). I played around with all of the features and functions before I began the installation to make sure everything was on tip top shape. Then I began to plan the runs for the cables going from the control box to the light strips. About the light strips, holy cow those things are robust! They are encased in a metal sheathing with some sort of clear rubbery coating on the side where the lights shine and to this day mud, dirt, and debris have not affected them. When I was first installing the front and back I made a bit of a mistake. It was getting dark outside so I wanted to move in the car to work on it where there was light. Well I accidently ran over the cable that I had attached to the rear strip and it yanked the strip out of the spot I just had it sitting in and bent the entire strip into a soft Crescent shape. I almost freaked out until I bent it right back into its normal shape and it functioned just fine! However one of the metal prongs inside of the connecter at the control box got messed up by this mishap and caused all of the blue diodes in any strip connected to it not to function, but that was fine by me as I only intended to use green anyways. Everything else during installation was smooth up until it came to mounting the side strips. My 2011 Honda Accord Ex sedan had no grommets, holes, or spots to attach the strip to. There was also a rubberized coating on the entire bottom of the sides of the car that would not allow me to drill into the metal to mount the strips. So I would up using zip ties, which have held very very well, and different kinds of tape on the ends, which has not faired so well. Every other day one of the strips would lose its tape do to rain, or wind and it would hang about 3 centimeters from where I had it mounted. Eventually I was able to use packing tape (of all of the tapes for some reading that was the best and is still holding on after 2 weeks) to hold up the strips. After that I had to run the rear strip and found out that the cable was about 2 feet short of where I needed it to be. Maybe if I had mounted the control box in a more optimal place it would have worked but I already had a cozy spot for it near the top of the engine bay (another thing: it is mush easier to just mount the control box in the engine bay somewhere near your fuse box, rather than inside the car). It is worth mentioning that my car is longer than the average sedan by about 8 inches so your milage may vary. So I just bought an extender cable that was in the recommended section under this product and it worked great! Everything functions except for the rear strip's blue diodes but that is from my dumb self messing it up. I would highly recommend this product as it definitely turns heads and is a great way to personalize your car without doing anything to drastic to the vehicle.

The media could not be loaded. This is likely the best kit I've seen for this price range. Many other "eBay" kits for this price or around it appear to be much cheaper quality and the wiring is too thin to last. However this kit's LED strips are very durable and secure. I've driven in heavy rains and rocky roads in my lowered car and they are still perfect. Install was super simple (although I did take a lot of time to ensure wiring was perfect and protected from any moving parts or areas where it could rub due to movement). Both remotes are very convienent and offer a range of colors/patterns to play with. Hardware included I would give a 9/10. Not bad for a universal kit, however I ended up using different bolts. The kit allows you to screw in small brackets in which the strips zip tie to and is surprising durable. Instead of using the small screws the kit came with to hold the brackets, I was able to use screws from a local hardware store that went into my factory holes that held my sideskirts. For the front and back bumper I bought bolts that held the brackets so I could drill through the bumpers plastic and bolt down on the other side with a matching nut to hold the brackets. Wiring itself appears durable but I backed it up with the black wire loom covering from a local auto parts store. Plenty of lead from the strip and also 4 extensions with the kit to extend from the strip to the control box wherever it is in your car.Now for the only bad I noticed; with the angle of my front and back bumper, even with the car lowered 2", the LED strips were visible under the car. This bothered me a lot as it looked like tacky light bars under the car, and could have been something easily fixed by the company if they had some sort of built in lip just enough to surround the edges of the strip. Personally, I found some angle iron that fit just enough over the strips and painted it black and used the same bolt/bracket system to hold it and the strips on the bumper. Problem solved, and didn't look half bad. Again, in my opinion something that could easily be changed during production, in my opinion.Other than that in short, this really is a great kit and I love having it in my car! It is worth any tweaking you might have to do to have it fit perfect on your vehicle!*Photos included are a mix of before and after I installed the angle iron to show the "light bar" look I described. The video also was taken before I installed the strip on the rear bumper.