sb componentsRaspberry Pi Zero Case Protective Case Cover for Raspberry Pi Zero & Zero 2 W - Black

Having two different kinds of backs (one for GPIO access) is a great idea. Keeps the Pi enclosed and protected.

Nice case for a Pi Zero though it is designed for a Pi Zero classic I needed it for a the new Pi Zero 1.3. It did not fit the new Pi Zero due to it's new Camera connector. It took some work to remove some of the internal plastic but then it fit still beautifully (without the camera connector being available externally but that's not a problem as I don't need it)

Just what I needed. Using to setup multiple Kisok machines for use in a community effort to bring awareness to the Census coming up. Support personal will have no issues connecting the devices as the cases are hi-lighted with raised text to show what cable goes where. Favorite case thus far for the raspberry pi 0w for the novice user.

Very slim and nice case for Pi Zero

This works perfect, however it doesn't allow room for the plastic piece that is apart of the external camera io. I just broke the plastic off since I had no intention of using a camera. It works perfect now. Screwes to keep it in place, two different covers for exposed board or completely covered. 4/5 stars instead of 5 because it wasn't perfect.

As an earlier reviewer said, this case does not fit the current 1.3 version of the Raspberry Pi Zero with the camera connector. However, removing some of the plastic from the lower case to create a notch to allow the connector to fit will work. It's pretty easy work if you have a Dremel. If you wish to use the camera connector then remove a little more of the plastic.The case comes with a set of four screws to secure the Zero into the lower case but the fit is snug enough that you may find the crews unnecessary.

Fits snug Open or Closed. I like it, just works.

Case is too snug, bent plastic ribbon slot in the back. Also case is clear and not black as shown in the picture.

Le boiler est en parts de plastique solide et de bonne qualité. Il se clippe facilement, bref je ne l'ai pas encore utilisé sur le Pi mais ça devrait aller. Mais il manque des patins... or il y a 4 emplacements de prévus.

Not a lot to say about this little case but here goes....It's all plastic construction and as the listing says it's very quick and easy to insert your Pi Zero into and it just clips shut in a matter of seconds.Again as the listing says there is access to all ports and there is a choice of two tops to the case one a enclosed one with no access to the GPIO pins or one with a cut out to allow GPIO pin access so whatever you needs this little inexpensive case has you covered.My one very minor gripe would be it's quite difficult to take the Micro SD card from the Pi while inside this case but apart from that it's a really good buy.

Fa quello che dovrebbe fare. Tutto ok

Das Gehäuse passt einwandfrei, incl. Öffnung für den Kameraanschluß (ältere Rezensionen beziehen sich auf eine ältere Version des Gehäuses)!Habe einen dieser silberfarbenen Standard-Alukühlkörper montiert und das Gehäuse läßt sich mit einem minimalenLuftspalt dazwischen noch perfekt schließen. Wenn man einen dieser höheren, schwarzen Alu-Kühllörper verwendet, dann vermutlich nicht mehr!Die Schrauben passen auch und im Unterteil sind sogar Lüftungsschlitze integriert, ein schönes Detail, wie ich finde.Zwei Sachen sind anzumerken, welche zwar meines Erachtens nicht negativ zu sehen, aber vielleicht für den einen oder anderen interessant sind. Erstens sind Gummifüße im Bodenteil vorgesehen, aber nicht im Lieferumfang enthalten (steht auch nicht dabei, somit i.O., wenn man welche braucht sind sie immerhin vorgesehen), zweitens hat das Gehäuse zwar eine Wandhalterung (Schrauben/Nagelöffnung), kann aber nur vertikal aufgehängt werden, allerdings kann man das Gehäuse mit Pi Zero sicher auch mittels Power Stripe vertikal an einer Wand befestigen, somit auch kein wirkliches Problem.Für mich das ideale Gehäuse, passgenau, schlicht und funktional!

Appena mi è arrivata la scatola, ho visto che era di buona qualità. E' fornita sia del coperchio "chiuso", che quello che mette a nudo i connettori per i segnali. Inoltre vengono anche fornite le vitine per fermare il Raspberry Zero sul fondo.Ho subito preso il Raspberry Zero per montarlo dentro, e li è arrivata la sorpresa: non ostante fosse tutto a misura non si riusciva a chiuderla.Ho così scoperto che il tappo del connettore video per non rovinare i contatti del Raspberry cade sul bordo della scatola e ne impedisce la chiusura. L'unica soluzione per chiuderla senza forzare e deformare il tutto, è togliere il tappo di sicurezza.Questa soluzione però non mi è piaciuta, anche perchè non so se con l'ingombro del connettore e del cavo flat, se mai vi collegassi una videocamera, la scatola potrà essere chiusa. SE NE SONO DIMENTICATI. PECCATO, se no avrei dato 5 stelle.Quindi mi sono armato di Dremel e microfrese e mi sono creato le mini scanalature.Spero che per i prossimi modelli provvedano a fare in fabbrica quello che ho dovuto fare a mano.