Epoxy Resin 2.25 kg Fibreglass Kit | Professional Quality Clear & Odourless Lamination and Resin with Hardener and Gloves, incl. English Instructions

Absolutely the best resin I've used, and more for your money. I'm ordering my 3rd batch of it. Just a shame it's often out of stock. Clear resin, easy to weigh out. Runnier than others but if you leave it a while will thicken if you need it to. Hardly any smell, sets quickly and able to demould in less than 24 hours. I'm just about to try the deep pour as I'm so impressed with this make. Bubbles also disperse by themselves quickly. Would defo recommend. Why did you choose this product over others?:Cheaper for larger amount. Great quality, bubbles disperse quickly, unless you are adding flowers, which you can pop with cocktail stick.

i haven't tested the product yet but what i received looks like a quality product. well packaged and the supplied gloves were not the expected flimsy plastic ones, but proper work gloves.a multilingual glossy instruction booklet is supplied with it and it is clear and easy to understand, unlike the poor chinese translations we are used to.i'll come back and adjust my feedback when i've had a chance to test it both in casting and laminatingEDIT: laminating... not a chance! Sets way too slowly to be practical.Casting though was flawless, takes a LONG time to set fully but water clear no problem

Excellent product, mixes easy and is super clear and hard. This is the first time I've used anything other than 1:1 ratio. The resin is very thin/runny compared to others that I've tried so not as good for some techniques where you need the resin to be thicker but great for the right projects. Will definitely order again as it's great value for money and lovely finish.

Start with the pros: sets extremely quickly, after an hour or two. Very easy to use, clear instructions. Mixes well with colours. Not too thick so pours quite easily. And free gloves is always nice.Cons: because it sets quickly this means heating to remove bubbles is not an option unless you get water temp or heat pad to quite a low temp I have had quite a few catastrophic pours by heating too much and this set off an awful reaction.I am yet to use a vacuum to remove bubbles, however with it setting so quickly I can only assume this might still cause problems, nevertheless I will try.Bubbles, I may be delusional in expectations, however I still tend to find the slightest bubbles here and there with a straight mix and pour, maybe I am too vested on perfection. However overall it is quite clear, just don't expect crystal clear.

Extremely happy with this productI have tried lots of resins but this is my favourite for value and workabilityNo smell. Very little bubblesVery clear

I am very disappointed, I've mainly bought this product for sealing stones and other small similar projects, but it's been a complete disaster.First, I've noticed that the Resin bottle part I've received was a yellowish colour...I've followed the instructions given, but the result was a very uneven seal, runny in some parts, wavy in others. A real pain to fix afterwards, and some of my pieces have been ruined !Perhaps as casting it is not that bad, but like I said above, the resin was out of date.I wasted money, I will not buy again. I will go back to cheaper resins which are surely doing a much better job.Check the batch date before opening it !

This resin is fabulous, mixes very easy and goes clear after about 90 seconds of mixing (but still mix for 3mins). The resin is quite thin and therefore the colours may run more and not very good for covering a canvas for example as it just runs off, although it is self leveling. Found this very good for casting and coasters or dishes. Dries to a tough, clear, shiny finish.. Which is what everyone wants. I also found that on some pours it left a film or scaley like bits but think that's due to the room temp being too low.

GUTTED - Ordered and received my kit at the end of March 2020. Wanted to order more on 8 Apr 2020, but the seller (a German Company) is no longer trading on Amazon. I'm still digging to find out if I can buy their resin elsewhere.First things, first: MIX IT FOR NO LESS THAN 3 MINUTES! I have seen many posts on social media that the resin is cloud/streaky when hard/cured; the two components must be mixed well for no less than three minutes. Make sure your room temperature is between 18 and 22 degrees centigrade (as with nearly all epoxy resins). I use a pressure pot to extinguish any bubbles, but, like with any resin, if you are very careful and gently warm up (not heat up) the resin part of the mixture in a basin (no more than hand-hot temperature), then the resin will increase in fluidity and have less opportunity to catch and hold air as you mix. I have seen videos of people who say that you should use plastic or polyester stirrers and not wood ones, but the fact is that it's all in the stirring. Gentle stirring will produce less bubbles.The resin hardly smells at all - and any odour is not pungent, unlike polyester resin (which absolutely stinks).Hardening time: well, that all depends on what temperature the room is. However, this resin does product an exothermic reaction at all thicknesses, so be careful.All, in all, the resultant product IS water-clear; I sand the hardened cast with 120 (you can start on 240 grit!), 180, 240, 320, 400, 500 and 600 grit Abranet strips, then wet sanded with Micro Mesh pads from 1500 through to 12000 grits. Following this, I polish with T-Cut, then (in my case) Maguire's car polish. The final result is GLASS-LIKE!