Roopose Galaxy Note 9 Screen Protector Tempered Glass,3D Curved Full Coverage Liquid Dispersion Tech Repair Function Easy Install Kit for Samsung Galaxy Note 9 (2018) -2 Pack

Yes, you can save a lot of money, here. Just as good as the Dome, but for less $. Pretty easy to install. I love the stickers to protect the speakers and ports - Wish there were 4 sets instead of 2, I covered EVERY possible that could get glue in them. Lol. Glue went on flawless and uv lamp was great. It's a nail lamp! Lol So, I can use it again and for multiple uses. The glass screen felt sturdy and my sensitivity is actually better. My last screen protector left my phone less sensitive. Full adhesive protection. Glue actually worked right and was kind of oil based, so it was easily cleaned up with an alcohol pad. I recommend you have a rag with alcohol handy for clean up. All edges were cleaned easily and the screen protector is securely glued to the phone. I don't expect lifting.

Tried a few different protectors before finding this one. All of them had a thin strip of adhesive around the edge and would never seal properly. So glad I found this one! Comes with two protectors, glue, guide, and glue curing light. Total time to install, including meticulously removing dust from the screen, was about 5 minutes.I strongly recommend doing this on a few layers of paper towel, in case some of the glue seeps out during the curing process. Also, you'll need a VERY level surface. When you put the glue on your screen, it makes a very liquid puddle that will roll right off if you're not level. You place the screen on top of that puddle and the glue expands to cover the whole screen, at which time you use the curing light to make it solid. You'll need a nearby outlet for the curing light.Since it uses UV light to cure, don't do this outside during daytime. Or near a window during daytime. In fact, best just apply this screen protector at night from the comfort of your kitchen table.

I have installed a similar one on my wife's phone so I was familiar with the process. I ended up having to scrap the first one. The tray that the phone sits in was extremely snug and apparently I did not have it all the way in. The tabs that stop the bottom of the screen protector weren't seated all the way and the glass slid under it making the protector too low. I started to cure the glue before noticing. An oversight by my part.The second one went on perfectly. The tray was extremely snug and was worried about pushing too hard to seat it properly. However it worked fine. Protector looks great and performs excellent.

This screen protector is very nice when installed properly. However, it can be quite challenging to install without clear and precise instructions; oh and a UV light that's not working. This was the case with my attempt to install this screen protector. Let me just give you all a tip when applying the glue. Make sure you put something under the provided tray (at the bottom of your phone) to avoid accidentally tipping the tray with your hand before you are ready for the glue to spread over the phone. Otherwise, the glue will run all down the sides of your phone and it will be a waste. The instructions don't give you that tip. You should also make sure the UV light is working before you get started to avoid running all over your home looking for something to cure the glue.I gave this screen protector three stars because both screen protectors and glue were wasted because 1.) the glue ran all down my phone on the first one because they don't tell you to put something under the tray and 2.) when I tried the secound one, I found out the UV light didn't work. The USB port was broken. I emailed the seller and they sent me a replacement, but they only sent the one pack. I think they should have sent me the same thing I purchased, which was the two pack because as I mentioned they failed to provide information to avoid tipping the tray while applying the glue and the UV light was broke. Anyway, I like how the sides and edges adhere to the phone, unlike other glass screen protectors that don't completely lay flat on the screen. However, you should be careful of what type of case you use. Some cases that have the front that snaps on may lift the edge of the screen protector leaving you with small bubbles under the screen protector.

Review in 3 parts:Customer Service- Seller is willing to listen to issues and problems. I contact them in regards to having one of my screen damage (damage was not done by me), and seller was willing to send me a replacement.Communication- Seller is very responsive to emails with questions, concerns, and issues. Response either happen within 24hrs or less.Product-Installing product is not simple. It will take about 45 minutes with planning, understanding, and doing. Watch the video, it is helpful, but it does not show you what to do when you have a bubble. If you have a bubble (either by accident, or whatever reason), use the plastic card to lift the corner of the screen slowly until you get the MOCO liquid to retract to the bubble area. REMEMBER...SLOWLY. Once the bubble is out, slowly place back the screen back down. I MEAN SLOWLY (like snail slow). Once the screen is on with no bubble, then use the blue light as instructed, and leave your phone ALONE. Do not use, touch, or move it around for at least 8 hours. The adhesive fully cures in 24 hours, but the adhesive is hard enough for light use. I suggest doing this over the weekend or a day where you don't need to use your phone. Once cure, it is good. I've have mine for about 1 month already and no complaints.LONG TERM REVIEW: Coming soon...