Greyghost Mr Fix 9h Nano Coating Kit Super Ceramic Car Coating Hydrophobic, Car Paint Protection Anti Scratch Glass Coat, High Gloss Auto Ceramic Polish 9h Hardness Ceramics

**2 year update (September 2025): the coating gave up the ghost and no longer beaded up after a full Decon on 09/2025. A combination of being too busy, weather not cooperating (constant rain to constant 90deg+ weather) prevented me from doing a full decon until the fall in 2025. I did some touchless washes to get winter grime off, and clay toweled once early spring, but by the time I did the full decon I couldn't bring the beading back. Still a good product, but I think I'm going to switch to the Turtle wax hybrid solutions spray wax. I might need to apply it more often, but it also doesn't really need a full polish to apply it. The attached picture is about 1 year after application in an area that salts it's roads in the winter. I bought my bottle on here from Tracfy, and it went on really easy. You do have to properly prep the surface, which is the real hard work. Full wash, remove any waxes or coatings, then polish the surfaces you plan on coating. There's a lot of labor to get to the easy application After the salty winter, the pores of the coating had become clogged with salt and iron, so it needs a good decontamination wash to bring back the beading and water sheeting. Soap, foam, and agitation wash are not enough to bring the performance back. You need to do iron decontamination and then use a waterspot remover to soften the the salts that have deposited into the coating. So I first did the steps through an agitation wash. Then I sprayed on DIY Detail Water spot remover all over with some wiping to dis-embed the salts. And for final decontamination I used a P&S "clay" towel combined DIY Detail Iron remover (Claying the car and iron decon at the same time!) with Adam's car shampoo foamed on for lubrication, and a bucket of the car shampoo to dunk the clay towel in between panels. It sounds more complicated than it is, because a lot of the stuff is premixed, and the "Clay" towel slides really easily with all the lubrication. The work is very fast. DO NOT USE AN ACTUAL CLAY BAR. A clay bar will damage the ceramic coating, but the P&S towel is not actually clay, and is safe on the coating with enough lube and the iron detailer. After that deep clean you're good to do less involved maintenance washes until you go through another winter.

I have used this product four times on three different vehicles, ranging from a one-year old car to a five-year old truck with a significant amount of paint wear. And then I used up the remainder of the bottles of the product on things like our clothes washer and dryer or our picture windows onto the rear patio. The prep process for using this ceramic coating on a vehicle includes the following. 1.) Foam shampoo / three-bucket wash. 2.) De-ironing / de-contamination. 3.) Compound polishing with an orbital polisher. 4.) Clean all surfaces with isopropyl alcohol. 5.) Apply the ceramic coating. 6.) Buff off the remainder of the ceramic coating with microfiber cloth. 7.) Clean off the hard plastic on the low surfaces like the rocker panels with something like Back to Black. My experience is that doing steps 1-4 one afternoon or evening, and then steps 5-7 the next morning makes the process a little more survivable - trying to do it all in a single day can be pretty exhausting. Buy a big package of microfiber cloths, as you will use them on most of these steps. This particular product goes on quite easily, and removing the excess after ten minutes or so of set time is also simple. When we first started a bottle on the new cloth and hard sponge, we needed to really soak it thoroughly in order to get going, but once the cloth had some saturation, everything works smoothly. At the conclusion of the application process, the vehicles all looked good, and the surfaces were indeed hydrophobic. We did all painted, chromed, and windowed surfaces, and that includes the interior of all the windows. We even did the alloy wheels and the headlights and turn signals. The first time we went overboard with the isopropyl alcohol cleaning, but that is probably better than under-cleaning. Even the well-used older truck, with some noticeable paint degradation, looked significantly better once we had finished. We spent more time with the de-ironing/decontamination and then the compounding, doing two runs with the orbital polisher to help correct some of the more obvious paint chips, on the older truck. This put us in a good position for the ceramic coating. In the months since our first use of this product, the vehicles are much easier to clean. Bird poop, squashed bugs, tree sap, and road dust all just wipe right off. The picture windows on the back of our home are also easier to clean, and the washer and dryer are slipperier, too. And in every application, the surfaces look glossy and deep, which is a big improvement. This is true even for a white car, but the deeper or more jewel-toned your vehicle paint is, the more effectively the product works to liven up the color and depth.

I have used three of these ceramic coatings including some really expensive ones. This is by far the best at least in terms of value and also equal to significantly more expensive compounds in terms of endurance and hydrophobic/protective qualities. We have used them on both paint and windshields, and just recently I did a set of alloy wheels with good results. On windshields they act as a kind of semi-permanent Rain X, improving wiper function and visibility. In lighter rain all we don't even have to use our wipers anymore. Car still repels bugs, bird droppings, etc., and paint generally looks like new. Pros: 1) Exceptionally easy application including provision of a very nice small sponge pad which allows an even application of a very even thin coating. You need to be fairly economical with this to do an entire car and its windshield. 2) Sets up quickly in a matter of 4 or 5 min. depending on temperature and humidity. Don't let it sit too long! After several hours you will not be able to take it off except with polishing compound. 3) Easy to take off with almost any towel but microfiber works best. 4) Multiple uses. Can code countertops, wheels, carpeting, windshields, etc. etc. 5) Fairly easy to take off if you let it sit for too long or miss a spot when you're toweling off the car – surface will develop a funny kind of strange haze that's visible in certain light and from certain angles. The service will not feel as smooth on those areas. A light application of polishing compound – don't use rubbing compound! – removes this fairly easily. Cons: 1) does not include a renewer or ‘over coating’ – but for 17 bucks what do you expect? 2) No other real issues or problems.

Usato dopo il detail con le saponette di argilla è davvero ottimo. La mia auto è nera ed tornata a brillare da sembrare nuova. Bisogna lavorare a piccole zone, ad esempio uno sportello per volta, oppure prima il cofano e poi il paraurti ecc . Nelle recensioni del prodotto c'è un professionista che spiega bene come usarlo. Vale la pena cercarlo e seguire le sue indicazioni.

Ich habe die Versiegelung fuer den Lack und die Windschutzscheiben der Motorräder angewendet. Ausserdem fuer den Autolack und unlackierte Kunststoffteile. Gute Vorarbeit ist wichtig. Ich empfehle den Lack nach dem Waschen mit Reinigungsknete von Baumharz, Teer und Fliegendreck zu befreien. Andernfalls konserviert man die Schmutzpartikel. Der Lack wird dabei geglättet. Danach mit silikonfreier Hochglanzpolitur bearbeiten (z.B. Rot/Weiss). Anschließend Entfetten mit Isopropanol. Die Versiegelung gleichmäßig auftragen. Je nach Wetter 10-15min. antrocknen lassen. Danach die Ueberstaende wegpolieren. Die Oberfläche nicht anfassen. Eventuell das Fahrzeug nach Beendigung in die pralle Sonne stellen. Das scheint das Aushärten zu unterstützen. Kunststoffoberflächen werden aufgefrischt. Es entstehen keine weissen Ränder. Die Versiegelung ist Wachs und Polymer Versiegelung überlegen und definitiv ihr Geld wert. Achtung: Das Wegpolieren der Ueberstaende nicht vergessen! Nach dem Aushärten wird es sehr schwer die Reste zu beseitigen.

super produit assez simple d'utilisation et résultat surprenant

I was a little sceptical when buying given the cost of having a ceramic coating applied professionally. Having made sure that the surface was clan and free of contamination I applied two coats with some to spare in the bottle. It goes a long way! The instant shine has remained for a good 12 washes now and still looks just as good as when first done. When applying many microscopic pinpoint stone marks in the laquer finish disappear as well. Excellent product and I have purchased more to coat two other cars.

El producto funciona perfectamente y es fácil de aplicar.lo único que no haría como dicen las instrucciones es hechas 4 gotas de producto hay que hachar más,si no apenas se empapa la esponja y otra cosa que no viene en las instrucciones es que si lo hechas directamente en la esponja está lo chupa todo yo le puse encima un paño de los que trae doblado por la mitad y he he las gotas encima unas 10 gotas más o menos.por lo demás seguir las instrucciones limpiar bien la superficie hecha el producto horizontalmente y verticalmente (yo luego le di en círculos también ) lo deje 5 minutos y retire el exceso con otro paño de los que trae limpio y listo. Aa y con paciencia y sin prisa.