OTUAYAUTO Front Windshield Washer Nozzles - Replacement for Ram, Chrysler, Dodge, Jeep - Replaces OEM #: 4805742AB 5113049AA 5116079AA 5303833AA Premium Fluid Nozzles Spray Jet Kit (pack of 2)

It works fine, I installed them on my 2008 Chrysler town and country and the spray was too low on the windshield. But I was able to adjust the angle of the spray by cutting the included spacers. Wiper fluid leaks a little on the hood but otherwise it’s effective. I’d still recommend it over the expensive OEM ones.

⭐⭐⭐⭐⭐I couldn't be happier with the Front Windshield Washer Nozzles! They're a perfect replacement for my Chrysler vehicle, fitting seamlessly and functioning flawlessly. The premium spray jet kit ensures a strong and consistent spray, effectively clearing my windshield for optimal visibility in all conditions. Plus, with a pack of two included, I have a spare on hand for future use. The fact that they replace multiple OEM part numbers adds to their versatility and value. Installation was a breeze, and I'm impressed with the quality and durability of these nozzles. Overall, a fantastic product that I highly recommend to any Chrysler, Dodge, Jeep, or Ram owner in need of reliable windshield washer nozzles.

They do not even spray on the windshield, water hits below the wiper arms in the off position and Noticed that one of the nozzles has the tip broken off and useless!!!! I'd say at minimum they owe me 50% of my money back!!!!!! But they don't seem to agree and it's either send them both back and get refund or send em both back and they will send two more. But I really only need one but wanted the other for a backup. So I guess I just get screwed out of 50% of my order!!!!!Pure JUNK DO NOT BUY THIS PRODUCT

it fits to 2015 dodge grand caravan..and works fine but it spray water lower side of winshield not middle of that and i can not adjust that!thats why i gave 4 star..other then it is ok..

These snapped right into place and actually spray the windshield.

The media could not be loaded. The nozzles are the same style, design, and fit as my factory Dodge (2013 Journey). They are extremely easy to put in, literally just snap into the holes and then you reconnect the water line tubing.If you are even slightly auto tech savvy these are a no brainer and a simple repair/replacement.If not it will take a little thought and work to remove and or re-install tubing especially if replacement tubing is needed but entirely doable without the need to take your car to a shop and pay (usually $50 or more) to have them installed.Unfortunately in my case the water spray from the nozzles are not lined up correctly for my car and windshield. They work, however the water spray is not fanned (1), not even (2), and it doesn't reach the center (or even low center) of my windshield (3) as stock (OEM) nozzles do.(1) Water spray is not fanned means the spray of water is not in a fan shape or spread across the "stream" of water. I'm staying away from the word stream because it is Not a stream of water Nor are windshield spray nozzles supposed to be a stream. They are supposed to be a fan of evenly distributed water across that fan shape so as to cover a wider/larger area of the windshield. Some car's windshield nozzles may spray more of a stream but will still be in a fan shape to help cover and wet down a larger area of the windshield. In any case not being fanned and the spray leaning more towards a stream of water is not necessarily a bad thing as it still provides the same volume of water and the saturation amount may be equally as important as coverage of area (fanning).(2) The water spray not being even refers to the fact that on each nozzle the water spray is not evenly spread across its spray of water. From a nozzle more water comes from different areas of its spray/"stream". As in, one side of the water spray has a larger amount of water coming out than the other portion of that same water spray.(3) The water spray barely gets to the bottom of my windshield and most just squirts my hood or under the windshield wipers. This may be due to the fact that these nozzles cover a very wide range of car makes and models and will fit since the holes they fit in are all the same. However, some makes and models of cars may have their wiper nozzles further or closer to the windshield, than others, meaning the distance from where the nozzles sit to where the hood ends, and windshield begins, may be different. Angle of hood & the angle of the windshield will play a factor but for most, if not all, the vehicles listed that it will fit will all have extremely close/similar specifications. I even tried to move or adjust the nozzles to see if I could manipulate the water spray or move it to hit higher on my windshield but to no avail. The distance from the nozzle to the edge of my hood is 5" (pictured).The distance from the nozzles to the middle of my windshield where the OEM nozzles sprayed, and optimal location, is 24" (pictured). The spray from these nozzles only get to almots16" (pictured) which is too low to get full/best coverage.They are a good value for their money if you are willing to risk a potential less than optimal spray location (maybe yours will work better than mine did).They Do work and they Do spray the windshield but may not do so, well enough, to help properly clean the windshield, as in my case.Only recommendation I could give is that if you have a distance from the nozzle to your hood edge and/or distance from the nozzle to the middle of your windshield similar to mine then you may have the same performance and may want to look at other companies instead, or just eat the cost of an OEM pair from an auto parts store or your car's manufacturer dealership.

Why did you pick this product vs others?:I have replaced both of the factory windshield sprayers due to weather. Both times, (2 years apart) it got colder than anything near normal lows. The water freezes, the pump continues to spray for a few seconds and they are done. I bought these and now have a spare. they spray just like the factory models but they are a real pain to mess with. Don't be afraid to go ahead and break them when removing them. Unplug the water line. Snap them in place, and attach the line. The mess is fighting the insulation under the hood that hides the lines. It will help if you are about 6'4" and can reach everyting over the fender of a 4x4 ram truck.

These fit and function in my 2015 Ram 2500 perfect!