CLC Custom LeatherCraft 5-Pocket Cell Phone/Tool Holder - 1105

Well built case, but not a good size for Motorola G7 Play 2024. The phone "will" fit, but just barely. There is not enough velcro contact for me to trust using it. It is a good fit for my older Motorola G7 2000ish model. I wish the 2024 model fit, but won't knock the case for that. It is a great case for smaller phones!

This thing is great. Is is a tad on the bulky side but no larger than it needs to be in order to hold a few usefully sized tools. An excellent balance of size and functionality I think.The sides of the cell phone pocket are elastic, and the pocket is deeper than most modern phones are thick, so the pocket nicely conformed to snugly fit my phone despite it being wider than the CLC spec of that pocket. CLC site says approx 2.5"W, my phone case is 2.875"W, and it looks like the pocket would still expand to slightly higher than 3"W. My phone is a HTC EVO 4G LTE w/ 4.7"diag screen which was big before the Note showed up. The pocket would hold my phone with a bulkier case, but maybe not a Note. The height of the pocket is such that the edge of my phone sticks out just enough to not muffle the speaker. My phone is 5.375"H. With the flap closed there is still room for a slightly taller phone. It is also enough room for a headphone cable to easily fit with a right angle plug. A straight plug fits too because of the way the flap is cut narrower at the top but it is marginal on my phone as the flap puts pressure on the plug in a bad way but other phones may fit better. The inside front and back of the pocket have a little padding with a nice soft fabric to go against the screen.The front pocket does not have any elastic, but it is just wide enough to hold side-by-side both a multitool and a 8-pc folding hex key set (with metal frame only, plastic frames were all too bulky to fit). The front pocket is deep enough that I put a stubby bit holder on the bottom of it and the multitool and hex keys fit on top. Total dimensions of what I fit in the front pocket are 2.25"W x 5.5"H x 0.625"D. Either my Leatherman Wave or original SwissTool fit well.In the middle pockets fit a small screw driver, 0.625dia handle 5" total length, could fit up to a 6" length. The other middle pocket I fit a sharpie and a pen, you can fit a third writing utensil in that pocket if you really try but its tight. There is a gap between the two middle pockets, that while not an actual pocket, can also fit a pen or pencil.With my phone and all the tools in there the flap closes to halfway between the minimum and maximum that the Velcro allows, so there is nice adjustability for longer or shorter tools while still keeping the flap snug.The flashlight loop is pretty self-explanatory and tight at the 0.75"dia of my flashlight. Anything wider wouldn't fit. The keyring clip is plastic and probably will break eventually but the fabric loop it attaches at seems solid so that could be easily replaced by a metal keyring clip.The initial reaction from those who have commented on it has been something like "is that an 80s vintage cell phone?" but they are nonetheless impressed when they see inside. I am told it also looks great next to my CLC impact driver holster, I just wish that holster had the belt clip too.A nice product that I am very happy with. If you think it is too big or small there are certainly other options for different phones and more or less tools. For my needs it turned out perfect. Goldilocks likes it tooSummary of my kit, loaded pouch is 1 lb 13 ozPhone (HTC EVO 4G LTE)Multitool (Leatherman Wave or SwissTool)8pc folding hex key set (1"W x 4"H x 0.875"D)Stubby bit holder (1"dia x 1.5"L, in bottom of front pocket)Screwdriver (0.625dia handle 5" total length)SharpiePenPencilFlashlight (0.75"dia)I hope this helps you make a well informed decision on the product either way. Enjoy. Or not.

I bought this with the intention of carrying a Leatherman Charge TTI tool, 2 bit kit trays, the bit extender, a single cell flashlight, and my iPhone. It comes close, but doesn't quite work for me. It is sturdy, well-sewn, and has an excellently designed belt clip. However, the rest of my review will speak specifically to my multitool use case.The back pocket fits an iPhone 5 without a case. It seems like it would be a tight squeeze with a case but sides are elastic, so it should fit.The front pocket holds my Charge but the pocket is deep. If I were keeping this I would attach a lanyard to the tool to pull it out.The middle pockets could fit an AA cell light, like my Inova X1. They are a bit too deep for the bit extender. However, they don't fit the bit kit trays. The only place to put the bit kits would be the cell phone pouch and that's an inch too deep and a scratching risk. The flashlight loop can fit an AA cell light, like my Inova X1. The belt clip is strong and secure. It feels like the pouch will stay put once I slide it into place. Even though belt clip is attached to the vertical belt loop, and that to the horizontal belt loop, there is not a lot of play and the pouch sits close to the body. It does not dig into my side when I sit.

This cell phone/tool holder is sturdier than I expected, and has two secure options for attaching to belt or waistband. I use the sturdy metal clip, but there is a wide belt loop available as well. I use this mainly to carry small items I like to keep close at hand while gardening or working around our property, that I used to carry with limited success in pockets. Aside from my iPhone 6, I keep my leatherman, a stylus pen, a small cutting tool, and a small pair of scissors that I find handy, within easy reach, and I use the the loop at the side for a marking pen. I am not using the plastic key clip on the front...yet. My only concern is the durability of the clip over time, as it is plastic, but so far it appears that it would work well. I think that if there is a weakness at all, it would be with the clip, as I haven't had much luck with plastic clips, but it is low profile and since I probably won't use it, it will be fine for me. I love the design of the flap that holds everything securely in place. It is tapered in over the top of my cell phone so that it doesn't block the microphone or speaker which is handy as I like to listen to music or audiobooks and there is easy access to the earphone port if I need it. My stylus pen is roughly the length of a long gel pen, and while the case holds it snugly so I don't lose it, I can grab it quickly without having to lift the flap. The inside of the cell phone pocket and the underside of the flap is lined with a soft material that has a suede feel to it, but I assume is microfiber, an unexpected and nice touch for the price, and is paired with sturdy stitching all round so it should last a long time. The velcro closure is larger than I expected, and it won't easily come undone accidentally. The overall profile is compact and unobtrusive. It gets the job it was meant to do done, and does it very well. I give this compact belt phone/tool holder a solid five stars and I highly recommend it.

Great utilityFor those who wear these type of pouch, this works great.I have been wearing something like this for years.A multi tool, and a flashlight are the main things I carry but there is room for more!

Sturdy construction but is extremely to tight for iPhone 15 pro max.

Very well made.

perfect for the tools I carry