GameSir Kaleid Wired Controller for Xbox Series X|S, Xbox One,Windows 10/11 & Steam, Plug and Play Gaming Gamepad, Transparent Video Game Controller with Hall Effect Joysticks/Hall Trigger

- UPDATE!! The latest firmware and app version allow for setting the polling rate up to 1000hz!! This means the input delay can be shaved down to sub 1ms!! Best value PC gamepad on the market hands down!! - The T4 Kaleid is a great gamepad for many reasons, and not just because that sexy black PCB and clear shell! There are so many great features this gamepad has to offer as well as long lasting components and low input delay for a responsive experience. - The controller is recognized as an Xbox 360 gamepad in Windows 11 (XB1 in Steam) (X360 in reWASD) - 4ms(250hz) consistent input delay in PC mode (8ms gyroscope) - 8ms(125hz) consistent input delay in Switch mode (used reWASD to emulate X360 gamepad to measure) - Overclocking this gamepad did nothing as the jitter is already non-existent and polling rate locked - I did not test the other input modes for the gamepad - The hall effect joysticks in this gamepad are not made by GuliKit but feel very similar to the ones found on the 8-BitDo Ultimate and less like the KingKong 2 Pro - There are no anti-friction rings but the plastic around my joysticks is very smooth not catching at all - Using the software, you have total control over the deadzones of both joysticks - You can set the joysticks to raw mode through the software and completely disable the outer deadzone offering more precision however this will affect the circularity of the joysticks in both PC and Switch mode (PC mode turns from a circle to a circular square and Switch mode turns completely square) - With the outer deadzones capped to 95% I was getting near perfect circularity readings - Face buttons are super long lasting but will be subjective, I wish the plastic was matte, not glossy but I enjoy that they are cushioned and offer a satisfying click much like a mouse (they take getting used to because there is no feeling of bottoming out) - Capture button is only detected when in Switch mode - While I do prefer symmetrical joystick layouts like the DualSense offers, this gamepad is very comfortable for long periods of gaming (very lightweight and ergonomic) - The gamepad is wired only, but for me this was no issue as I grew up in the 90s and offers longevity as well as reduces e-waste - The included cable is very decent quality, thick and braided but keep in mind that the hole on the gamepad where the cable goes will only accept oval shapes - The D-pad is not terrible and for single inputs is very accurate however I still prefer the membrane ones found on the 8-BitDo Ultimate especially for games like Mario and Donkey Kong - The back buttons are limited to being mapped as the other controller buttons which is expected, but they are very easy to change on the fly without the use of software - Lighting effects have presets and brightness levels that can be adjusted on the controller without need for software - Vibration levels can be adjusted without software - ABXY layout can be swapped on the fly without software - You can easily change between input modes by holding the GameSir logo button and ABXY buttons (by default my controller goes into Switch mode when booting into Windows so requires me to manually change it or unplug and re-plug) - Can set hair trigger mode without the use of software (hold M button + L or R trigger for about 4 seconds) however this does not work in Switch mode probably due to Switch using digital triggers - The triggers are also hall effect and feel very smooth and can be completely adjusted using the software - Contrary to other people, I had only 1 issue where the software crashed when I was changing lighting effects on the controller and personally I love that the software is easy to use and not bloated like something you might find by Razer or Logitech - Overall, I just can't think of a better gamepad for this price point. I own a KingKong 2 Pro, 8-Bitdo Ultimate, and have upgraded 3 sets of joy-cons with GuliKit replacement joysticks, and these are the best feeling hall effect sticks on the market right now in my opinion. I've tried to go back to my DualSense Edge a few times since my purchase and I just can't, and for the price of just 2 replacement pot sticks from Sony you could be the proud owner of this masterpiece! Keep up the great work GameSir!

I've had the GameSir Kaleid since December 2024. I love it. I love the micro-switch face buttons and the Hall Effect sticks. I mostly use it to play third-person shooters and action RPGs. I set my dead zones on the sticks to 0.0 and I have no drift. It's a wired-only controller but I'd rather have a wired controller than deal with batteries and the cord is a nice length. Because I wore the pads off of the thumbsticks on my previous Microsoft Xbox One controller that I used on PC (and my Xbox 360 controllers on Xbox360 before that), I also picked up some GameSir thumbstick caps when I bought this controller so I don't wear out my thumbstick pads. I've never actually used it without the thumbstick caps so I can't speak to how well the thumbstick pads wear. I find the controller very comfortable for long play sessions and so far it has held-up well to the stress I put on it. (I play a lot.) I've been thinking about ordering a second one for awhile--I buy things I like as though they're going out of style--so when I saw yesterday that Amazon had it for a lower price than I paid before, I placed my order for another one. There's nothing wrong with the first one, I just want a spare for the future. Aside from connecting it to a family member's Windows 11 laptop once to update the firmware on the controller when I got it, I've been using the controller on Linux Mint. The below information relates to my experience using the controller on Linux Mint. I'm using it via Steam Input on Linux Mint 22.2 to play Steam games. On Linux I currently have no control of the RGB, but it's fine; I just forget about it most of the time. I didn't buy it for the RGB, I bought it for the Hall Effect sticks and triggers, and the micro-switch buttons and D-pad. After booting my Linux Mint system, the Xbox logo button is not lit-up and the analog sticks on the controller are not detected until I disconnect it and reconnect it. Then the Xbox logo button lights up and the analog sticks are detected until the next reboot. (The other buttons, oddly, continue to work fine whether I re-plug it or not, it's just the analog sticks.) Linux Mint doesn't see the controller inputs outside of Steam (I might be able to fix that but haven't bothered since I don't play any games outside of Steam) but Mint does see the headphone/microphone jack on the controller as a sound device when the controller is plugged in. I often use it as my preferred headphone jack since the controller has a long cord. (Holding the M button while pressing the D-pad up or down adjust volume.) Anyway, it's a great controller so I'm buying a second one.

I purchased the GameSir T4 Pro because I already had a GameSir G3W and really liked the build quality, but wanted something wireless. I also wanted a full-sized controller with a few extra buttons. The two additional trigger buttons under the controller work well for N64 and Genesis emulation, as well as FPS games. Personally, I wish the controller were a little bigger. I previously purchased a SteelSeries Nimbus I returned almost immediately because it was far too small to fit my hands. Comparatively, the GameSir T4 Pro is more comfortable. Back when I was a teenager, I used to really dislike huge controllers - like the Dreamcast, original Xbox, and Sega Saturn controllers. They all felt like unwieldy platters I'd sooner eat off of than use as game pads, but even back when I had smaller hands, I could get used to them. As an adult, there's no getting used to controllers which are too small; the result is always accidental button presses and impercise control. While the GameSir T4 has required some getting-used-to, inaccuracy hasn't been a problem. Build quality is excellent - just like the G3W. The plastic is thick and the controller doesn't bend under stress. The button action is smooth, analog sticks are solid and don't drift, and the Dpad is very high quality. One thing I've always noticed with most 3rd party controllers is that the buttons generally slide around or stick in place. That's not a problem on Gamesir controllers. My only two gripes are that the RB and LB shoulder buttons are placed a little too high for easy access, and the M1 and M2 buttons underneath the controller are very clicky. Okay, I have one more gripe actually; Compatibility. I purchased the M4 to pair with an Nvidia Shield TV Pro, and while it does connect, it's pretty finicky. While the T4 Pro does list compatibility with Windows, Mac, Android, and Nintendo Switch, each connection is achieved in different ways, which can be a bit complicated. It actually comes with a radio frequency USB dongle that has to be plugged into Android devices to connect. That's not an issue with my Nvidia Shield because it features standard USB ports, but compatibility over Bluetooth will highly depend on which version of Android your device runs, and the included USB dongle may be troublesome for folks wanting to use the T4 Pro with a smartphone running a recent version of Android. I've also noticed that despite a full battery and connection to the RF dongle, disconnects are pretty frequent. If you set the controller down for more than a couple of minutes between game titles, it'll completely disconnect and need to be resynced. That wouldn't be an issue if the controller featured a quick-connect button, but GameSir has opted to use cryptic button combos to turn on the controller and connect it with various platforms. Each platform requires a different button combination, and it's tough to keep those memorized when swapping between Android, Windows, and game consoles like the Nintendo Switch. I think it's pretty rad the T4 Pro is compatible with so many different platforms, but getting the controller connected and keeping it connected are a bit of an annoyance. I've got to say, though - I was surprised when I opened the box and found out the T4 Pro does indeed include a USB-C charging cable. That's one of the many reasons I've returned previous controllers. If I'm spending $35-50 on a game controller, I don't want to make a second trip to the store for an additional $20 charging cable. Kudos, GameSir! Thank you for being considerate! The Gist: All things considered, I think the GameSir T4 Pro is an incredibly well-built controller and features an attention to detail rarely found in other 3rd party game pads. I could easily be fooled into thinking the T4 Pro was manufactured by a 1st party company like Nintendo, Sony, or Microsoft; it feels that good. Connecting the controller could be easier, and it'd be nice if the RF could work across the 5GHz band since 2.4GHz is usually pretty saturated in tech-savvy households, but I can't say I've ever experienced a disconnect mid-game. I have noticed some input lag on specific platforms like Android, but I believe that has more to do with my Android devices then the controller itself. It's neat that the T4 Pro supports built-in button-remapping on specific platforms, but good luck doing that without reading the manual every time. I would suspect most players are going to opt for a software remapping solution instead. I do find it a bit troublesome that there's a potentiality slipping and hitting the wrong combination of buttons while in a game could result in accidental button remapping. What's worse is that once the controller is accidentally reprogrammed, there's no simple button combination to reverse the effect. If you're on-the-fence about a purchase, I would highly recommend GameSir's entire product line; not just the T4 Pro. I've purchased multiple controllers from GameSir, and they've all been a joy to use.

Totally worth it. Better than console brand controllers in every way. Be sure to download the Gamesir nexus app and update the firmware and you won't have any issues. You can also calibrate the joysticks and triggers easily in the app. My primary use is only on Windows 11 gaming PC. Pros: - Responsive and spam able x,y,a,b buttons. - Triggers and joystick can be calibrated to avoid dead zones via the Gamesir Nexus app - Triggers are accurate as advertised. You can even test it in the app, down to 1% pressure/usage. - Price is better than overpriced console controller - LED's look great - USB cord is long - Great vibrations. Just as good as console controller. No noticeable difference. May even be better. Cons (if any): - I personally don't like buttons behind the controller which I accidentally hit while holding but is an added feature that some people may find use. - Can be a new experience for those used to console controllers. Not sure if these buttons are exactly mechanical but they are as responsive. Some may confuse this with cheap feeling (chiclet style?) x, y, a, b buttons.

I had to post this review because there are so many contrary answers even from the Seller. The T4 Pro works with Android perfectly via BLUETOOTH for Game Pass and Stadia. It also works with Wireless Dex from my Note 20 Ultra on my smart TV to play Stadia and Game Pass. It functions as an XBOX controller on my PC via the included 2.4ghz dongle. Bluetooth to Nintendo Switch works great too. The T4Pro buttons all feel great on my fighting games. I've tested it with Killer Instinct, Street Fighter and Smash Brothers. The bonus buttons on the back work perfectly for jump and crouch/slide in COD. The phone clip works fine but I wish it could be set to any angle between fully closed and fully open. Only one angle holds for me and it snaps open or shut after that. I have to use it without my bulky camera-bump hiding phone case on. A smaller case would probably be ok. Overall this controller is sturdy and feels premium, but just not as premium as an official controller. I would say its 90% there. I wish this version had the swappable button layout of the G4 or lit up different colors/letters in the transparent buttons depending on the pairing mode (Android/PC vs Nintendo Switch button assignments). The only features missing are NFC and the Switch calibre feedback called HD rumble, both of which are not required to enjoy a full 99% of games in existence on these platforms. Most other controllers lack these two features as well. Other bonus feature are the linear triggers than can be used as gas and break pedals in racing games due to their analog sensitivity. This feature is only Android and PC compatible I believe, as Nintendo chose not to support analog triggers for Switch games. Hope this review clarifies a few things for everyone!

This controller is amazing, and I’ve been through pretty much all of the paces as far as controllers for Xbox goes. Elite Series 2, Scuf, Gamesir G7, modded original controllers, and even some PC controllers using an adapter. This beats ALL of them. The Elite Series 2 and Scuf are still the best for the “look and feel”, but as for the function, this controller is the best. The buttons are mechanical, which feel amazing to me. This difference means that instead of the button slowly depressing and then at some point making contact and giving input, a very specific amount of weight will make the button go down immediately, potentially giving you a tiny boost in reaction time. All of the buttons are mechanical, except for the home button, remappable buttons on the back, and the thumbstick buttons. Next, the thumbsticks and triggers. They are next level. The part you’re going to notice most is the thumbsticks, as you’ll be able to lower your dead zone in all games to zero or 1 without getting any drift. That is simply impossible on a normal thumbstick, since the standard margin of error for the dead zone of those style sticks is usually around 7%, meaning you’ll get drift in some direction anywhere under that number. Having no dead zone means every single tiny movement on the thumb stick is very accurate, allowing you to control recoil and aim better. Third, the look and feel of the controller is actually really good! As I said before, it doesn’t beat the Elite 2 or Scuf at all, but the clear plastic is surprisingly thick and has a quality feel. The mobo is on black PCB which looks nice. And the lights are an added touch, with a ton of customization, all the way down to making multiple color “phases” for one lighting profile so you can make all sorts of patterns and stuff. Overall, this controller is going to be the #1 all around controller in my books for a while, probably until Gamesir releases something else or maybe if Microsoft actually decides to make an Elite with hall affect sticks. We shall see There is, however, one critical flaw. On the current firmware, my controller sometimes turns my Xbox back on when I shut it down. It seems to happen intermittently so there may be a specific thing I’m doing that I’m not aware of, but that means it could probably happen to you too. The only way to stop this loop is by unplugging the controller. Furthermore, when the console is successfully turned off, the controller won’t wake the console up from sleep unless you plug it in. Pretty annoying but a price I’m willing to pay for a great controller. I’m hoping this could be fixed with a firmware update, but we’ll have to see.

Compared to the original Xbox controller this thing feels cheap. I haven't had any issues with stick drifting yet though after two months so that is an upside to this controller. I noticed some design flaws, though. One being the left trigger gets stuck sometimes when you press it and you then have to press the side of it to get it unstuck. The first time this happen i heard a cracking sound. So don't know if something broke or what, but the controller works perfectly fine, and there are no cracks that can be seen and it's only done this twice in the two months of owning it, the second time it happen, it didn't make the cracking sound. Once while playing Rocket League a week or so after buying it and then once again while playing Fortnite about 5 days ago. It doesn't happen nearly enough to be something that i worry about, but it does the cheapness of the controller and makes me worry about the longevity of it.. The other design flaw is that there is a huge gap between the sticks and the housing. Allowing hair etc to easily get inside your controller and being a see through controller this is not the best thing. You end up being forced to look at hair inside the controller if you turn on the lights that are inside the controller. So you are pretty much forced to turn them off if you don't wanna look at it anymore. I feel like the sticks and the housing should have less of a gap so that this doesn't happen so easily. That is about all the issues that i've noticed so far after a little over two months. It's a good controller, but held back by a few issues. I wouldn't pay $50 for this controller again to be honest. If you can get it in the $30 range. I would pick it up. Hopefully MS makes a controller with HE sticks as they feel way higher quality, but are not worth the money when they stick drift after a few months.

TLDR Best under $60 wired controller on Xbox, way better than the stock Xbox controller. FACE BUTTONS All mechanical except for the 'home' button. This really helps know you have clicked a button all the way, which is harder to tell on a membrane button. If you have never used mechanical buttons before, you have to try it to see how much better it is than membrane buttons. THUMBSTICKS Hall effect sticks, way more resistant to drift than regular potentiometer sticks. If you use a controller a decent amount, a regular potentiometer thumbstick will eventually drift, causing you to have to keep moving up your deadzone. Hall effect sticks don't have that problem because the sensor doesn't rely on friction. Hall effect should be the standard going forward. I use after market thumbsticks, not like kontrol freeks where you can just stick the tip on. But literally the thumbstick plastic that goes on the thumbstick module directly. For this I had to open up the controller with a T6 screw driver, (don't forget the screw under the bottom sticker). But if you do this you will probably void warranty. You can use regular Kontrol Freeks if you want, using the PS4/PS5 size, however I change out the thumbsticks completely to make it more like an Elite Controller. I use the ExtremeRate thumbsticks specifically. The one suggestion I have for Gamesir, is to make interchangeable thumbsticks in the future. This is literally the only feature missing imo. THUMBSTICK GATE The part where the thumbstick rubs up against the shell also has an anti-friction ring, which is an improvement over the original Kaleid and standard Xbox controllers. If you don't have this anti-friction ring your thumbstick stem will wear out eventually, which you don't have to worry about now. SHAPE The shell of the controller closely resembles a standard xbox controller. This is better than the Gamesir G7, as the handles are slightly more flared out on the Kaleid, which is more ergonomic for your wrists. WIRED This controller is wired and uses a USB C which is great. I only play wired anyway, so I don't have to worry about batteries. Where the cable inserts into the controller is also recessed a little to provided the cable end a little more protection which is a really good touch. TRIGGERS Really great, pretty much like standard Xbox controller. SOFTWARE Download the Gamesir Nexus app from their website and has all the typical customization, like remapping and color choice. Really good, no complaints.

Love GameSir controllers, replaced by Xbox ones as I must be very unlucky as all of them kept disconnecting. Very comfortable and high quality, works great

The controller works perfectly. Great value for money

I was recommended this controller by an American i play Division 2 with on the PC, and i assumed it was a 'Turbo Fire' type of controller, as in, you just hold the button down and semi-automatics like pistols and rifles would fire like fully automatics do. Sadly, it's not that type of 'full auto'. Forget about the LED lighting. It's nice, but it's not what you're using to play your games. It's just a nice touch. I have mine set to 'solid white' which of course as with any other LED lighting, gives off a very light blue tint, which is fine. My only issue is with the software. The controller still works as it should without the software, but if you want control lighting and set trigger options, and just see what is actually going on, you need the software. Not everyone has a Microsoft store account, and not everyone can get around downloading the files from their own site and cobbling it together. I downloaded it from their site first, and it didn't work. The program wouldn't start at all. Then i tried it from the Microsoft store, and again, it didn't work. Then for some strange reason, i booted up my computer, and all of a sudden, it works. I don't even know LOL With everything up and running, i have to say, depending on how long it lasts of course, if it meets expectations, then i'd buy another one of these controllers instead of an Xbox controller. Also i have to say, for a "Made In China" product, to not be put off by this at all. It's very well made, and i have to also give credit to the sticks, triggers and buttons. Compared to an Xbox controller for PC, this beats the Xbox controller easily. The lentgh of the cable is great too, i actually can just sit back in my chair, which is around 7ft away from the big screen TV, and not worry about the cable one bit. This whole idea of people being wary of products "Made In China" has always been silly. It has nothing at all to do with China or the Chinese folks. Instead, it has everything to do with the Western companies who order things to be built in China to whatever specifications they desire. The complaints everyone has about products made in China, only exist because companies are the ones cutting corners, ordering products to be built with lower quality parts and materials. and that's that.

Some interesting choices but a very capable controller. I hope it lasts many years and so far, I have no reason to believe it wouldn't. The latency is amazing. XInput reports 0.955ms. I purchased this on the latency claims and the controller delivers. I have now swapped over from the Gulikit KingKong 2 Pro for the 90% reduction in input latency that is definitely noticeable. I opted for the wired T4 Kaleid over the latest wireless Gamesir offerings as they are limited to 250hz polling I believe. Joysticks and triggers are great, smooth, no resistance, definitely hall effect. All the face buttons are micro-switches I believe. So ABXY feel like mouse clicks instead of a standard rubber dome controller face button. Weird but weighted nicely and very responsive. No complaints. The D-Pad switches are softer, feels more like a rubber dome switch setup but all feels good. The rear macro buttons can be assigned to another button or a series of buttons on the fly. Also clicky micro switches but placed nicely and very responsive. Build quality is great. The textured and gloss plastic all looks and feels great. No soft touch coatings to deteriorate and become sticky. The cable is a standard, replaceable type C cable. The type C port is also recessed quite far into the body of the controller to protect the port from cable stresses. Finding a replacement cable may be more difficult but the port should be protected from most drops etc. The screen printing on the exposed internal circuit boards looks great. A shame that the actual electronics aren't visible but still looks cool. Lighting is bright and colourful, maybe a little excessive but looks great. I setup a slow light profile in the software with a max brightness of 5% on each LED. Less blinding now. The windows software just about works. Windows thinks it has crashed every time it opens. Once it loads and recognises the controller, click into a profile and set the polling rate to 1000hz! The software holds 4 profiles and only one is loaded onto the controller at a time. Each profile can remap each button, adjust joystick and trigger output range (dead zone), vibration intensity, adjustable gyro output and have 4 lighting modes. If you want the reliability of a wired controller, I have found nothing better then this one so far. ORDER PLACED 29 September 2023 TOTAL £35.69

So far so good! I just got this in the mail. It arrived super fast. The lights are vibrant. It's practically the same size as my old controller (maybe like a centimetre smaller), as shown. Fits well in my hand. The cord it comes with is super long (maybe like 10 ft). The sticks feel good. The buttons are satisfying to click. I haven't tried it in game, so I'm not sure how well it works for that but it's a major update to my last controller (as it had controller drift).