SupershieldzScreen Protector for Samsung Galaxy S23 Ultra 5G, Tempered Glass Film for S23 Ultra, 3D Curved Full Coverage Protectors, 9H Hardness, Bubble Free, Anti-Scratch, Touch Sensitive - 2 Pack

After installing this, the phone wouldn't even allow me to register a fingerprint, saying that the senso was possibly wet and to clean it. Avoid if you want to use this feature. I've installed numerous screen protectors since the S22 and now S23, I did it correctly, but the "hole" is VERY prominent on the screen afterwards. To quote their description online, "Bubble-free installation, screen protector to automatically stick...". Should've suspected things when the paper instructions regarding the fingerprint hole included "...which might cause slight bubbles...use scratchcard or finger to remove...".In short, yes it fits easily enough and sticks fine, but that ugly fingerprint section spoils the lot.

Failed to initiate the fingerprint reader once installed so had to return. It also has a weird circle that you can see on the screen for the fingerprint reader that is distracting. Especially annoying as it doesn't do its intended job.

Do not stay on the screen, poor adhesion and not even the correct size for advertised phone, why is this product still advertised, it's a complete misrepresentation. Bloody annoyed!!

The fingerprint scanner does not work with Samsung S23 Ultra.Used other screen protectors with same without any issues.Will be returning

finger reader doesn't work.

Lasts no more than a few hours before falling off...Dont waste your time or money..returnedAbsolute rubbish.Would give minus 5 if possible

Does not work for fingerprints

Bad. Fingerprint doesn't work, hole for fingerprint looks bad, edges don't stick. Overall just bad. In conclusion I think you can't really use glass covers for this phone.

The package included a notice to view the installation video before installing, but it was at the bottom of the case these shields came in. By the time I found it I already had tried and failed to install any of the shields without air bubbles. If you view the video first installation should be a breeze. I contacted the company and they immediately sent out a new package and I appreciate this level of customer service. Five stars because the bubble problem was my fault, not the fault of the product. Also five stars because (1) the shield is easy to install, (2) three shields are in the package, (3) high quality glass, (4) they are a perfect fit onto a Moto Z2, (5) they are completely transparent, and (6) touch sensitivity is perfect. There are no negatives about this product. If you are looking for an excellent screen shield for a Z2 or for any other phone Supershieldz makes a shield for look no further.UPDATE My screen protector developed a one inch crack two weeks ago. Since they are glass and we aren't always handling our phones with the greatest care a screen protector crack can happen. The important thing is that it prevented damage to my phone screen. I still had a spare screen protector from my first order and installed it. It takes some work to get all of the bubbles out but, with patience, it can be done fairly easily by following their video instructions. It took me several minutes to get it installed with no bubbles. I was able to get the bubbles completely removed. Still five stars.

Nice. I really like the slippery feel like its Teflon coated. HIdes smudges very well.Fits my moto z2 play well with about 1 mm inset all around inside a bumper case so its about 2mm all around the screen edge. Could be a bit larger but there are many case options that grab more or less of the screen edge so for compatibility its inset a bit.Installed as outlined on box. Used the included alcohol wipe first, and last as instructed. There are additional items that aren't well explained, but here's how to use them.How to best install1. Dust sticker: Pell this off and blot (stick it, pull it, repeat) all over the screen immediately prior to removing the backing and installing the protector. Any spec of dust left on the screen will leave a bubble there that you can't get out because its raised there. Just ambient dust in the air will do it. If you want it perfect you'll have to be in a bunny suit in a clean room.2. Guide sticker: Prior to peeling off the adhesive backing, lay the protector on the screen centered then use two (or all 4) stickers to mark the protector edges so you can hit the alignment mark when you stick it down.3. Lay the protector down from short side edge and carefully drop it down to the alignment stickers edge. I used the wax paper on the final short edge and overlapped it about 2mm to make sure it was on target. If its off target you can lift it back up with the wax paper edge and reposition it before committing to finally pulling out the wax edge and laying it down.4. Once its down for good, from the middle of the screen with one finger press lightly and all the air will magically force out to the edges. You will see the vacuum suck down the protector to the screen as it all goes clear from the middle out. "Wipe out" while hard pressing down the remaining air with the alcohol cleaining wipe you used to clean the screen prior to install. Hope this helps!Mine turned out great, aligned perfectly with just one dust spec and no other bubbles.

Shield seems thick and durable (time will tell). This is an ok fit for the Moto Z2 Play. It did not go to the edges. It also would not stick on the edges. I applied it well without touching it. For the price of a three pack, it's worth it. I don't know how long each one will last. But I'd buy them again as of right now.

I was really very surprised at the quality for the price! The best quality screen protector I've found, and I have bought a lot of them! It is with out a doubt the easiest to install as well. As the directions state: Make sure there is no dust. The company provides some stickers to make a handle for the screen protector so you don't have to touch the sides. (Finger prints prevents edges from sticking). I personally use a wide piece of cellophane box tape to make a handle, so I never touch the glass. I lined it up, lowered it and once it touched the phone glass it was as though it just sucked right down. Covered the entire screen with out bubbles. Only a few little spots on the very edge. One wipe with the micro fiber cloth, light finger pressure and it was perfect! I also noticed that the adhesive this company uses is the, strongest, the best! They really stick. Most screen protectors can be removed with cellophane tape, this one will not, they stay in place, stick to the glass. I plane to buy more for other phones, iPad and so on.

I read that screen for Moto Z2 did not break easily but did scratch. I bought these screen covers before the phone. So excited when phone arrived, I applied the screen cover without reading directions. ERROR. I had a good case, too. Dropped the phone. Everything all right except the cover. Several cracks from the corner where phone landed, extending across the screen. This time, I read the directions, watched the youTube video on installation, and followed the directions. The kit has some very well thought out tools to make installation, clean, accurate and dust and bubble free. I will break, but doesn't seem to scratch. It protects the screen. I bought extras so I'm ready for next time. Excellent product, all around.