ECHOGEAR 3 Monitor Desk Stand for Screens Up to 27" - Triple Desk Mount with Lock Down Clamp to Eliminate Screen Wobble - Adjust Tilt, Orientation & Swivel of Each Monitor Without Tools

So if you've ever spent significant time trying to align your multi-monitor setup, and you're looking for a better solution, this is as good as it gets.The design of this product is the best I've seen, and it takes several of the variables out of the alignment challenge.The horizontal bar is one piece of sturdy metal. So instead of the hinge-sag on typical monitor stands, you have a perfectly-level horizontal mounting surface. Then, the VESA mounts connected to that are done in an innovative way. The movement is much smoother than typical monitor stands and the tightening function/method is such that it doesn't change the alignment, like a typical allen wrench tightening does--so you take that variable out of the equation.Is it still difficult to align the monitors? Eh. It's not instant-easy and it's not perfect. Right now I'm about 2mm off on each, but it's consistent. I think if I mess with the screws on the center monitor VESA I can get it even. But it's definitely as good as it gets for what's available in the market. I've spent a Saturday getting two 3-monitor setups level before. This is MUCH easier/more consistent than anything else I've used.The mount for the base is a single-bolt, wide tightening plate, which is better than the typical two-bolt setup (where as you tighten one, it effectively loosens the other).My only complaint is that you can't go through the "pipe" to route cables... I'm solving this by zip-tying the cables together and then zip-tying the bundle to the back of the pipe to hide it. That might bother people if a perfectly "clean" cable install from behind the monitors down (vertical to the desk) is important. In theory you could drill a large hole in the rear base of the pipe and then route the cables over and through/down (it's an empty pipe with an open top, but with thick walls, maybe 3mm, so it would take a serious drill bit... could maybe be done with a Dremel and some time/discs/burrs).Pipe height is tallest I've seen... I'm 6'2" and have a standing desk, and I can get the vertical center of the screens nearly to eye level.The reviews that say this won't work on 27 inch monitors might be for an older/incorrect product. I DO have three 27 inch monitors installed and there was ~2 inches of gap between the three with everything spaced out as wide as it would go before I adjusted them to touching.Finally, with the monitors touching edges, the angle of the outer two monitors is ideal (for me, at least). It's the same as what I had done when I had fully-independent adjustment arms.Bottom line on this item is that if you like having your monitors vertically-aligned, this is the best solution I've found/seen/tried, and I've tried a lot. I'm going to phase this in at my office for everyone's monitor stands. Everyone else with various other typical (though expensive) monitor stands has given up--it's misaligned monitors throughout the office and it looks bad and I think it's bad for morale on some level. This stand fixes the problem.

So to start out with this thing is great, especially if you are looking to mount three identical monitors. It was an easy process, the instructions are not that great but honestly you can just look at it and figure it out.The biggest gripe is leveling the monitors, my left and right monitors are just slightly lower the main monitor, now if had more room around my desk to properly mount this and even someone to help I could get these perfectly aligned.Looking at the forums, it is pertinent you use the spacers on the outside screens, I used them also on the center one which made it a bit better when it came to leveling.I made the conclusion that the mounting bracket that goes on the rail has some play to it, and if you push up on it when tightening the mount it will add some vertical adjustment to the monitor, now I can only do so much as a single person and with my desk mainly against a wall. Looking at the brackets there is a little bit of space on the top and bottom, even when its fully tightened, so what I plan to do is add a little shim of some sort so that it adds a bit more vertical movement.I will update this review with the results after that slight modification if that works.Overal 10/10 I would recommend this over a triple arm gas spring, not only will those take more space, especially if you are against a wall.Side note: The reason I did not completely move my desk to properly mount this is because I have a metric ton of cables that I spent an agonizing amount of time organizing and routing.To get a sum of what I stuff I have on my desk:Two stream decksExternal USB DACWeb CamKeyboardMouseMicExternal doc for laptop and all the hdmi cables that go to each monitor from that docUSB Switch HUBValve IndexUPDATE: Got all the monitors to be leveled, the thing is its is important that all the mounts are put on the bar without the monitors, there for you can ensure that the mounts are properly snug with the railing. Second (you might need a friend, I used a stack of books) I used the largest spacers on the left and right monitors, I did not use any spacers in the center one. After doing that monitors are now uniform.

I recently upgraded my home office setup with the Triple Monitor Mount, and I couldn't be more impressed. The easy 3-step setup lived up to its promise, and within minutes, I had the freedom to adjust my monitors in any direction using the silky smooth patented joint design. No tools required, just pure convenience.The ability to tilt, swivel, and align my screens on the fly is a game-changer. The tension knobs on the rail allow me to customize the effort needed to move the screens, ensuring a tailored experience. Setting the perfect monitor height during the initial setup was a breeze, and now I can effortlessly adjust it with just my hands—perfect for those intense gaming sessions or getting through a crucial presentation.The space-saving feature is another highlight. Consolidating three monitors onto one stand freed up valuable desk space for accessories and, yes, the occasional energy drink. The built-in cable management system gives my setup a clean, finished look, making me want to show it off like never before.The custom setup options are fantastic. I can position my triple monitors horizontally or vertically, creating a professional finish that maximizes every pixel. The wobble-free clamp ensures stability even during intense gaming moments, and I no longer have to readjust my screens every time my desk gets bumped.This triple monitor mount is a true game-changer, and I'm confident it will be the last one I'll ever need. As I plan to upgrade my monitors in the future, the tool-free design will make the transition seamless. If you're looking to elevate your PC setup, don't hesitate—grab the Triple Monitor Mount today. You won't be disappointed!