MVPOWER Door Canopy Awning Window Rain Shelter Cover for Front Door Porch White(270 x 98.5cm/106.30 x 38.78 inches)

So like other reviewers I was actually under the impression from the description that the supporting arms were aluminium and this actually swayed me from another supplier that stated there's were plastic. To be clear the arms are plastic and the only aluminium pieces are the front and rear edges that slide over the Perspex.I ordered the white 3 section version and was a little disappointed when I opened the box to see the white looked more like cream! however once in the sunlight for an hour the white went back to white and matched my upvc rear door.once erected then awning feels very solid, I was a little worried about the direction of the Perspex, as I have previously brought a Perspex green house, I know, one side of the Perspex for the green house was uv protected and the other side not. I did ask the seller if this was the case, although quick to respond they mis understood my question, suggesting the answer was in the instructions but it's not! I assumed the side with the white film was to go externally and the side with clear film to be internal (facing down) hopefully I have guessed right other wise they will need replacing in a few years.As others have mentioned the instructions are not that clear but do hold most the information needed.Being an experienced trade man I put this up alone and found it straight forward once I got a routine, for anyone unsure the following may help you:First I put the middle section together (two arms and one panel),I found the fixing holes needed were exactly 88cm apart,As I had the 3 section one I worked out total length (88x3) and checked the positions making sure the top holes all would be drilled out in the centre (or close enough) of a brick (I had choice with my brick layout top or bottom fixing in brick the other fixing would end up in the mortar line so I decided I wanted the strongest fixing in the top- middle of brick & bottom fixing in mortar line) ,I then put my laser on the wall at the height of the top fixings (you can use chalk line or draw a pencil line with a level if you have no self levelling laser) marked all my top fixings (4 for 3 section). I didnt not worry about the lower fixings as these could be drilled out later!I then drilled pilot holes for all the top fixings and then set the depth and drilled out the 10mm holes.I then hung the middle pre constructed section of the awning using just the top fixings, once the section was attached to the wall using the top bolt fittings I levelled the arms and drilled out the lower holes (keeping the awning up and in place) and then bolted the lower fixing points to the wall (if you have 3 section awning like me dont forget to fit the end edge retaining screws into the aluminium but push the tips of the arms in first).If you have a single section then you are now complete, if you have more than one section read on:next I constructed one of the sides (single arm with perspex, aluminium edges and retaining screws as detailed in the instructions.the next step is where and extra pair of hands would had been useful as you have to slot the panel into the arms already fixed to the wall and once in fit and bolt the top fixing on the new arm.as before level the new arm then drill and fix the bottom fixing point (then fit the front end edge retaining screw remembering to push the arm tip in fully before screwing).repeat for the remaining side and job done get a tea and admire :)I pre assembled the middle section the night before, the flowing morning it took me about 1 and a half hours to get this assembled and tools packed back away again, its quite simple but does look a little daunting when you first open the box. the instructions could be a little clearer but do contain all the right information (apart from the Perspex rotation, if this matters).Any reviews that suggest this is not sturdy I believe have not erected it correctly.

Overall, very impressed. The packaging was of good quality (although one panel suffered a slight 'dink' in transit) and everything required was supplied. The quality of the pieces appeared very good and well thought out. Contrary to some other reviews, I found the securing bolts more than adequate and the long reach ensured a solid fit. The key is to use the correct (10mm) drill and not let it widen beyond that size, and to tighten the screw just enough to stop the end 'nut' from rotating once in the hole. Another key requirement is to get the measurements correct and I checked and re-checked several times before I drilled anything; a difference of only a couple of mm made all the difference and I worked to a tolerance of 1mm to be sure. I pre-assembled at least one panel to see how it all fitted together and did one panel at a time before drilling the next set of holes. I found that I had to cut 4mm off the length of each of the rear bracing aluminium struts to make a better bit, but a junior hacksaw was all that it took. I also drilled small holes to accommodate the small front-edge securing screws, which made it really solid. I managed to install the awning without any assistance, so it is possible for one to do it. While the components are very lightweight, once assembled and secured, it is very solid and looks good. How they will look in 2-3 years time, I have no idea but, at the price, I would have no hesitation in replacing them with the same type. Recommended.Update: Now on my 4th set and learning from previous experience. The first two sets lasted just over two years (one suffered in high winds). First observation is that prior preparation is essential. Pre-assembly and checking of measurements is vital for trouble-free installation. To maintain a ‘new look’ it is necessary to ensure that the open ends of the corrugated panels are sealed with a clear outside glazing sealant. This is most easily done by putting a 6mm bead of sealant in the channels of both the supports and front/rear bracing pieces. Failure to do this will mean that, at the first rain, the panel will fill up with water and, after time, the water will discolour and you’ll have a very unattractive awning! I also ran sealant along all edges of the panels to double-seal the join, which should guarantee a long life. The sealant also adds to the strengthening of the awning when it flexes in the wind.I still think these are a good, cost-effective product, that works well and looks good - providing the panels are sealed. While the competitive price is maintained, I plan to replace the awnings every two years; however I notice that the good reviews are resulting in higher prices!

Bought at my wife's suggestion as she wanted a canopy for the back door but didn't want to spend much. This is a low priced plastic version of the kind of metal thing sold at B&Q for several times the money. It has metal runners front and back to give some rigidity and once in place it looks like a more expensive item. The shades themselves are also made from plastic, a corrugated flexible version, and it's put together with a screwdriver (but use one with a magnetic tip, as the screw holes are recessed and can't be reached using fingers). And if it's too big you can use just the one section rather than fixing two together.Definitely easier to fit with two people, it can be achieved solo by careful measuring and letting one end hang down whilst moving your ladder and lifting the second side over your pre-drilled hole. I'd recommend using someone to help though.Overall, a low priced answer to the need for some back door (or front door) shelter.