NIDICI BLHeli_32 Bit 35A ESC 2-5S Brushless ESC Electronic Speed Controller RGB LED 3D Mode Support Up to Dshot 1200 MultiShot for FPV Quadcopter Multicopter (Pack of 4)

Things happen and I understand that, I'm very pleased to say the seller Nidici was,quick to take care of me as a customer and fixed the issue with no problems what so ever. Getting me fixed so I can get my quad back to flying in as short a time as possible.I am livid, I build a quad with F40 Pro v2 2400kv motors a F4 FC, Unify Pro and a Runcam Eagle pro the build flew excellent for about 45 seconds but was dipping the front left i just thought it needed higher idle speed and some anti gravity gain added in. in the first flight that i landed at 1 min 15 secs to make a pid adjustment and the next take off I noticed the front left dropping a little on throttle bumps more after the tuning that should have made it better telling me a esc was failing as I was coming in to land the way failed and the quad went wild... a total of 1 min and 40 seconds of flight and one of these escs fail causing a BRAND NEW 1550mah 4s 100c Tattu R-line 2.0 to get smashed denting the corner of the pack that is 3 cycles old... I'm VERY VERY MAD like for real very very mad... brand new escs that don't have more then 2 minutes of flight time on them and not pulled more then 20 amps threw (throttle end point at 85% and HQ5x4.3x3v1s on that motor pulls about 22 amps at 90% throttle) them and it cost me a BRAND spanking new 45 dollar battery...The esc clearly had failing fets from the start as that arm was dipping right off the bat means it was bad from the start and in NO WAY SHOULD HAVE IT MADE IT THROUGH QUALITY CONTROL. So now I have a bad set of escs and a destroyed top end battery... because of poor quality control, like in REALLY REALLY UPSET.

I’m not sure why these have such bad reviews maybe I just got lucky and got a good set. And then got lucky again when I built my friend an identical quad with the same escs that he purchased him self. Or it’s just people don’t know what they are doing when it comes to soldering? It’s very easy to hurt escs due to heat from poor soldering skills. The led lights are super bright and dshot1200 is awesome! Oh and I’m writing this review about 5 months later and around 100 packs thru my chameleon clone! I still like these escs. I intend to buy another for my nano wing I’m building

I purchased a used multi-rotor this summer that was fitted with these. One of them was faulty so I ordered a set of the same to replace one and have some spares on hand. So far I have been pleased with them. I did have one of the 4 arrive DOA, but the seller made it right. So unless they start popping for no reason they seem to be decently reliable well priced ESCs.

Nice set of 32bit Dshot1200 capable ESC's. My set came with the latest firmware and setup was a breeze, NO incompatibility issues with my setup (dys F4 pro or cl F4 racing), also a plus was that it came with wires soldered to the escs and heat shrink, one less soldering to do!! LED's are nice and bright too! Flew about 6 packs, it took me 2 packs to notice the smoothness and throttle control. If you have an F4 flight controller, go Dshot1200!!. Because your worth it.

All four work well and was easy to install. No issues and would buy again.

These 32 bit ESCs perform like a champ, no hiccups so far, the LEDs are a nice touch and can be programmed in Blhelisuite32! The only complaint is the heat-sinks on the mosfets are thermal glued on instead of using a thermal pad, which honestly isn't a bad thing, its actually better! Just no my taste as i run without those usually. Still 5 stars!

If you should crash with these on your build, and they still work, let them cool down for 30 minutes or they will burn out if you don't.

Excellent escs. I paired them with Emax eco 2306 motors. The quad is slicker than 2 eels in a bucket of crisco. Dshot 1200, they play music and I love the disco lights.Use blheli 32 to configure them. If you use the regular Blheli suite, it wont read them correctly.