SUPALAND Key Fob Shell Case Replacement Fits for Chevy Silverado Colorado GMC Canyon Sierra 2014 2015 2016 2017 2018 2019 2020 2021 2022 2023 Keyless Entry Remote Control 4 Button Cover M3N-32337100

This worked great on replacing the outer cover on my 2017 GMC Sierra key fob. Buttons are perfect. This shell is solid and looks a protective as the factory one and for cheap and no size or weight difference.

Fits great & works perfectly

I bought this to replace the terribly worn case for my 2021 Chevy Colorado. This is ONLY the case. You will have to disassemble your old remote and install the circuit board into this. It's not very difficult, just take your time. There are some good videos on YouTube that show the process. NOTE: You WILL break the tabs on your old case that attach the chrome side pieces to the black plastic, rendering the old case useless. It appears that this is just the way it is molded. I was surprised to find out the chrome pieces on this case are metal! BEFORE YOU SNAP THE SIDE PIECES ON, MAKE SURE THE REMOTE WORKS! I liked this one so much, I bought a second one for the future. Also note that if you have a back piece with the Chevy "bow tie" emblem on it, you can use it on the new remote as this one has just a plain back.

This was a replacement for a 2017 Silverado 4 button key FOB with a torn unlock button that caused the doors to unlock randomly and often. This replacement case had metal side pieces and metal battery holder. It came with the metal sides pieces detached so it was easy to open. The existing electronics and battery fit exactly into it and all 4 buttons functions well. The hardest part was taking the metal pieces off the original FOB. This FOB case is a good value and only took about 10 minutes to put together.

There was no way that battery from original was going to fit. I took my dremel and shaved off 1/32 of an inch of battery holder. This allowed me to place battery in snugly and fits well. The stock GM key fob has a silicone gasket and seems to be somewhat waterproof. The aftermarket fob has no gasket and would not be waterproof. Pro: It is much easier to open up the key fob than the GM original Con: In my case I had to shave down battery holder to load battery. No silicone seal for waterproofing. No bow tie emblem on back of fob. With that being said looks great and works. It most likely will retain its good looks because it is hard plastic where as the GM fob has a soft exterior that deteriorates quickly and looks terrible.

Not exactly the same but 99% correct. Old FOBs didn't come apart like the new ones. New ones work and look and feel nice. A little issue with seating one of the chips, but figured it out (bought 2). Good cost for value. All buttons work the same as the old ones did. Recommend replacing the batteries too.

Swap was easy and shell works perfectly

None of the reviews on this product provide useful information, so hopefully this will help some people decide. This is a CASE ONLY. You must have an existing key fob to buy this, and you must open up the factory one to switch over the microchip. This WILL NOT work by itself. Since you are switching over your currently working key fob microchip, you do not need to get it programmed at the dealer. If you need a completely new key fob, there are options on Amazon that come with a completely new key fob and programming tool for around $50. Those seem to be hit or miss, but it’s still way cheaper than the dealer. There’s not a lot of good videos out there on opening up the original key fob case (the only slightly hard part), and I don’t want to give any specific advice because I essentially destroyed my old case with a flat head screwdriver trying to get out the old microchip. I will say to pry open near the bottom where the key ring goes through. If you pry near the top by the lock/unlock buttons your screw driver will definitely be scraping up against the microchip. Now for this case: The original case has a rubbery front on it. It feels better, but wears out quickly (which is why so many people are buying these aftermarket cases). This one looks the same as the original from a distance, but it’s obviously cheaper quality once you feel it. I will say, the side chrome pieces are actually made out of metal instead of plastic, which was a nice surprise. The front of this case is a hard plastic, not rubber like the original. Who knows how long the front will last, I don’t think this key fob design has been around long enough for people to be able to test out the durability of it. However, for $10 a case, you really can’t go wrong. It’ll last long enough. I really don’t care that the front is plastic on this case. However, here is why I only give 3 stars. The case is just a millimeter or two, too small for the microchip. You can feel that the case doesn’t quite close all the way around the microchip, and when you snap everything together, it’s a tight fit. It doesn’t feel tight enough to damage the microchip, but just slightly too tight (as in front to back/ thickness of the case). Because of the tight fit, the buttons are extremely sensitive. You WILL get accidental button pushes in your pocket. Just note that that lock button seems to be the easiest to press. I don’t care if my vehicle locks again; however, if the unlock button were any easier to push, I would send it back. I would say these buttons are about 3X more sensitive than in the original factory case. Simply lightly placing your finger on the lock button will actuate the button. On my first trip to the store with the new key fob case, my truck locked on me again when putting the keys into my pocket. Since the horn honks when locking, I can see this becoming annoying over time. Like I said, since it’s the lock button and not the unlock button that is the most sensitive, it’s not as much as a safety issue. I wouldn’t want to chance accidentally unlocking my vehicle when putting the keys into my pocket. All that being said, I will still keep the key fob case. The dealer will charge $100 for a new key fob, and another $50 to program it. I went to the dealer, and this is what they tried to charge me. I’ll stick to $10 on Amazon for a new case, even with the poorer quality and performance. The extra cost simply isn’t worth a new one from the dealer. One more thing to note, I looked at pretty much all the cases available on Amazon for this key fob. Every one seemed to have something negative about it. Either too big, too small, or even poorer quality materials. This one seems to be overall OK on everything, and a solid 3/5 star product.

This key fob shell is a perfect fit for my Chevy Silverado! It’s easy to assemble, feels sturdy, and looks just like the original. It’s a great way to refresh an old or damaged fob without spending a fortune. Highly recommend it!

Producto de buena calidad, fácil de cambiar la carcasa, en cuanto a durabilidad ya veremos al paso del tiempo como se comporta..

Great product, no issues changing the insides of my old ones into the new ones, 2014 silverado.

Batalle para ponerle la pila, claro, no me dedico a eso. Yo solo pude hacer el cambio

Looks good, works well. Easy to switch over. Doesn’t have the Chevy bow tie crest but for the money it is a good buy?