VEVORMag Drill Press, 1300W 1.57" Boring Diameter, 2922lbf Power Portable Magnetic Drill, 810 PRM, 11Pcs Drill Bits Electric Drilling Machine for Metal Surface, Industrial and Home Improvement

Great product. Have put it through heavy use with zero problems.

You should note that the drill does not have a reverse run feature, which could be a deal breaker for some. It doesn't matter to me as I will not need that feature for what I am doing with it.I tested the ease of use and ran a 20mm through a 7/8in PIO steel bar stock. The (as described in the user manual) "twisted dough" bits do not need anything beyond a center punch for location and no pilot hole. In fact, it is better to have only a center punch locator point so the locator pin in the center of the bit can push out/eject the plug from the bit.It is surprising how fast you can pop a hole in heavy (1") steel. The slugs are ejected as soon as the bit breaks through and are smooth enough to be used for rollers or spacers. The hole (bore) has VERY smooth walls and sharp edges that gives you the precision needed for some applications. The drill has quite strong magnets and extra power. All-in-all this tool fits home use and most job requirements.

First off, it's a single speed. Cutting oil will not run thru the the 1/4" tubing from the mounted tank. Simple fix, remove tank, bring out pump gun with oil. My first project was cutting 3/4" holes in the tips of my lift forks. The annular cutter makes long streamers of metal and I had to shut down halfway thru to clear the head. Perfect job and the magnet held on well. Today I'm drilling weld holes in a 16 ga. panel using a 5/16' twist drill in it and it's very different. It doesn't start cutting as fast and I have to place down pressure over the top of the motor because the magnet won't hold it. Otherwise I'm happy with it and would recommend buying it.

The media could not be loaded. I only buy Milwaukee tools, but looked on this electromagnetic drill for a one time use. It is a very powerful drill. It went though a 6/12 steel beam like butter. The beam was already installed, so the electromagnetic feature was a plus to drill sideways and upside down.Great value for the money and easy to use!An extra tip to avoid overheating while drilling sideways or upside down, keep a sprayer with lubricant on hand to be used as needed.

First I'd like to commend the manufacture for packing it correctly. It has a wood bottom and the top and sides were 1/2" thick cardboard. Fantastic.I've been looking at a mag drill for a while since buying a "new" trailer and the thought of drilling a bunch of holes through 1/4 steel with a hand drill was never appealing to me.. I had to drill 18-20 1/2" holes through 1/4 steel (W10x19 I beam) for the side marker lights. I driller a couple of test holes in some scrap 1/4" plate to find the correct size for the lights and found the 21x30mm works for a 1/2" hole.It's not light and drilling horizontal holes is a bit of a challenge but a hell of a lot less fatigue then drilling these by hand. Actual drill time was maybe 15 minutes but with marking the hole and moving from place to place took about 1 hour. No chatter from the bit, it did not fall off, and drilled very nice holes.As others have stated, the magnetic base does get hot and not like kind a warm. Hot like in you could not hold it with a bare hand but with a welding glove you would be ok. I left it on overnight and it was hot. While drilling these holes it got warm but not enough that it was a problem or was hot to the touch. Not a negative just an observation.

Shockingly nice HSS cutters included but works with a queer size pilot that cannot be found after several additional Amazon orders. It’s a custom 6.34x77mm pilot that’s magically $50 alone anywhere you look.If you’re buying for a one time project, just get the drill and buy the cutters and pilots from a known good source so you can buy parts, otherwise you’ll end up with 45lbs of useless crap in the barn.Once you bust the included $2 pilot after drilling 20-30 holes, you’ll quickly find out the drill is useless. The drill doesn’t have enough vertical range or clearance for larger bits in the drill chuck provided and the normal taller pilots will not work either. The oiling reservoir and attachment is a F’n joke. Don’t even bother with it, just keep some lube nearby to keep the drill cool.It’s no surprise they used a custom short pilot due to the piss poor depth/height range.Ultimately, I would not buy it again. Make sure you strap it down, the magnets won’t hold it as you gently feed it, even on 1/2” steel plate. Almost took my foot off, can’t be trusted.Ended up finishing the job with a trusty Milwaukee. Save your money, time and frustration- don’t buy Vevor.

I've been a fabricator for 43 years. Recently semi retired and have been busier than ever. I have a fab shop and work by myself and drilling has become a pain, literally. I have arthritis in both my wrist and when a bit gets hung up, i pay the price. Got a stair stringer job which required a bunch of holes to be drilled so I read the reviews and decided to take the plunge. I just got finished drilling 92 12mm holes in 1 hour. Ive owned hougen mag drills in the past and, let me tell you, thos little drill works great right out of the box. I like the coolant tank on the side. Delivers coolant thru the middle of the bit. The magnet is strong. Set the drill up on a 1 1/2" wide flange. Cutter are good too. My advice is use the coolant, dont rush the machine and baby your cutters. I see nothing wrong with this machine at all. Awesome price for everything you get.

Drill works as it should but the annular cutters that are included cannot cut through anything. Swapped them with some higher quality cutters and the drill works great