10x2.125 Scooter Tire, 10 inch Solid Rubber Tires Tubeless Front or Rear Replacement 10x2.125 Solid Electric Scooter Tire for Gotrax G4 Xr V2 Ninebot F25 F65 Hiboy S2 Pro 2pc Black

Great tires just need to have the right tools and understanding to put them on. My local scooter shop wanted 100 to put these on. In my advice don't buy a scooter with tube tires get one with hard tires already on

These tires are well made and after installing, the ride of the scooter was very much improved and super smooth. Installation takes a little effort but really wasn't that hard. Installed both in less than 10 minutes after boiling. Watch a few vids on YouTube and follow the directions and you can do this. I boiled them for the full 20 minutes. Used plenty of dawn dish soap to lube up the rims and tires and a few long screw drivers to pop them on to the wheels. If it isn't completely straight when you first get it on the wheel, use a screwdriver or tire iron to pop the tire up a bit from the opposite side that is sticking up and it will settle into place. Really was a lot easier than expected to get these on.

Great product and works for a Gotrax G4 scooter. As all the other reviews say it was a massive pain to install as solid rubber doesn’t really like to bend that much. However after all the work the peace of mind I have knowing I won’t have to worry about flats is nice. Do know that because it’s solid rubber it will not absorb impact as well as an air filled tire and the ride will be a bit rougher. However I think the trade off is worth it for not having to worry about a flat ever again.

Just like many other reviewers the tire was difficult to install on the wheel:1. Heated in the microwave about 3 mins.2. Soap on the tire/rim a must3. After removing the wheel and disassembling I stood on the wheel (part w/o motor) and used a screw driver to pry the tire on to the rim. At some point it popped. This part was hard.4. Had to use clamps (see photos) to get the tire on the other side of the wheel and screw the wheel back together. Lining up the screw holes was actually easier than I thought it would be. Recommend taking off the brake disc during this step. I ended up bending mine slightly. This step was very difficult.5. Putting the cable back on was the most challenging step. I didn’t have pliers which would have been helpful. Matching up the arrows and getting enough leverage to get the cable back together was … frustratingI would say I’m average when it comes to being a “home engineer “ or handyman… this install was really difficult.

These tires were insanely difficult to install. I am a large, mechanically inclined guy with plenty of tools and rarely (never) gets stymied or frustrated with something as simple as this should have been..The only real instructions it came with said to search uTube for “Ninebot scooter solid tubeless tire replacement”, which did not link to the (or any) manufactures video but just random nice people out there who have created and posted their own videosSo basically there was no thought or effort at all given to providing their own instructions and they just leverage other people‘s work which is a cheap and unethical tactic as best.I searched through several videos before finding one that was specifically for the Segway Ninebot and was actually helpful. Even in the videos where the poster had obviously replaced these tires before it did not look easy, most used atleast 2 people, always big guys, no dainty ones who still fought and grunted to get the new tire in place.I followed the instructions I found on uTube to a T and still made no progress (except a lot of cursing) for nearly an hour trying to get this mounted. I boiled it as instructed and still it would not fit. I boiled it and then used my heat gun and still could not mount it. I finally recruited three other family members to assist and we finally got it mounted but the outside of the rim was significantly dented and scratched all over, all the nice looking orange paint strip was nearly destroyed so it looks pretty beat up now. This was only the back tire, given the difficulty and damage to to the back tire and rim I don’t think I will even consider replacing the front tire where the motor is in the hub of the tire.Finally, despite the width measurement of 2.125 specified by Segway and this product says the size is 10x2.25 there is about a 1/8” gap between the tire sidewall and the rim bead and does not engage at all with the bead. This gives the tire enough play when turning it feels like a Normal tire thats low on air. I actually worry a bit that in a sharp turn it might allow the tier to dismount or ”peel” itself off the rim on its own which is almost unbelievable considering the difficulty of mounting it..I know the benefit of not worrying about flat tires is enticing but I am not sure it is worth the frustration and cosmetic damage to the rim that results from the install.YMMV - Litterally ;-)

Fitted this to my sons Hiboy S2 pro. It is important to make sure the internal width of the tyre fits your wheel. We spent 2 hours trying to fit another tyre which was too big.The tyre came with a tyre spoon/iron.We boiled the tyre in water for 15 minutes, used dish soap around the wheel and while hot fitted using tire irons/spoons from Dr Roc. 3 hands helps a great deal.Overall 20 minutes to fit including boiling time. Fast delivery high quality, no complaints.This will not be easy if you don’t have tyre irons/spoons and don’t boil the tyre before install.

I put these tires on Ninebot Segway F25, they fit well, but the installation was extremely hard and tricky. It would have been a bit easier if the supplier shipped two tire irons instead of one.Ride becomes extremely stiff after putting them on! Considering going back to old tires, but dreading the installation.

Perfect fit for Hiboy s2 pro. I do recommend using two tire spoons for installation. I boiled them for 20 minutes before installation. I had previously purchased 10x2.5 tires for my scooter. They were a quarter inch to wide at the rim, even though I took 10x2.5 tires off. These fit perfect.