Jirvyuk Led Aluminum Profile, 6 Pack 1m/3.3ft U-Shape Led Channel and Diffuser with Transparent Cover, End Caps and Metal Mounting Clips, Led Strip Profile for Indoor Led Strip Lights(Transparent)

Very impressed and I’m an electrician lol

Very impressed with the quality of this product. Easy to install and performs the job well. No hesitation in recommending

I used this to hold innr smart lights on the underside of my velvet bed. They hadn’t stuck very well and were kicking around on the floor.My lights didn’t stick but they’d already lost their stick and we’re covered in fluff. It didn’t matter there was no need to stick as the cover held them in place.The clips were hard to get in partly because I’m suffering from vertigo and had to be upside down and I was screwing into upholstered velvet. Not a fault of the product but they did it. The clips held well I put in as few as possible because it’s under the bed and not seen and I’m not feeling well but quite adequate.I chucked away the white end caps I couldn’t see how you could use them as the wire wouldn’t go through the hole.They gave plenty of different sized screws, raw plugs and clips.The cover I cut with scissors I might have sawn it if I was putting it somewhere you could see it as it bends the ends slightly. The aluminium pieces were easy to saw, but do need the proper saw.Made a lovely neat job and my bedroom is looking beautiful, Just need to get some flooring and it will shoe off the lights better :-).

I’ve used these several times for LED tape and found them to be great quality and a lot cheaper than what is available elsewhere

I bought a 5m LED strip from Lidl and was looking for a good way to mount it on a ceiling. Came on Amazon, did a search and found this product. Fixed a piece of strip wood to ceiling (to aid installation), attached the clips provided to the strip wood, clipped the channel into the clips, fixed the LED tape, end caps and clear plastic cover, et voila fantastic professional looking installation. After reading other reviews, I made good use of the plentiful supply of channel clips (I used 5 per Meter long channel) including 1 at each end of the channel, butt jointing 2 channels into 1 clip and have had no issues with stability etc. I am very pleased with the outcome, wish I had have bought the LED strip light online as well as the one I had, had a couple of small sections where the LED's were not fully functional.

The quality of the product was really substantial considering it's size and the covers either slide on or push on; once together they look really smart; I was really pleased. I used 60 leds to the metre inside and the diffuser has been excellent at lighting up a large piece of glass art, whatever colour the lights are set on. The channel easily took the 12mm strip. The ss clips work well although for some I have drilled through the base of the channel and used a screw and put the strip on top. The end caps fit well, with a small hole for a wire (although of course led strips have a four pin connector on and so you have to cut a slot if you want to use the end cap as the connector won't go thru the hole).

Given how cheap these are, I expected a pretty low quality product, but these are pretty good. The aluminium extrusion is almost perfect, mine had some very minor bending, but nothing that caused any issus, easily corrected and was so slight you couldn’t tell just by looking at it.The kit includes everything you need including, diffusers a big pack of screws and endcap’s and the aluminium is very accurately cut to 1 m lengths . The only negative comment is the width shown in the image are not completely accurate, I found the width of the extrusion to be over 1 mm wider than indicated. So measure the width carefully if that dimension is important to you .

I ordered this product as I was putting some LED strip around a desk and didn’t want to see the bare LED’s and wanted to diffuse the light from them as well.It was well packaged and came with all the parts needed to fix to the surface. I had a tight space to work with so I ended up drilling holes on the back and fitting from inside which also worked well.I had to mitre a corner section and the cutting of the strips was easy with a hacksaw but what I did find was that by using an L connector on the LED strip, it became too big to fit within the Aluminium casing so I had to adjust the length slightly and just ran the plastic diffuser part over the LED without the base.I also wanted to be able to minimise the hotspot effect you can get from LED’s when they are too close to a wall and was a little disappointed that the diffuser mad lite difference to this as you can see in my picture with half on and half off.Overall I was happy with the product for the price I paid and would buy it again but maybe just not for the same application.