Araldite Standard 2-Part Epoxy Syringe Ultra Strong, Multipurpose & Solvent-Free Adhesive Works as Ceramic, Plastic, Metal, Jewellery & Glass Glue For Durable Bonding & Repairs 24ml

Araldite is the classic consumer grade epoxy resin - it's well known to everyone and been on the market for donkeys years. In my youth it came in two metal tubes, stored in a cardboard box. Mixing it involved guessing equal quantities of resin and hardener catalyst, and oftentimes making a bit of a mess. These double syringe versions are way better, making it easy to cleanly deliver exact, correctly balanced quantities to your mixing palate. Stir it together thoroughly, then apply.This is the slow cure version, which I prefer. You can buy rapid cure Araldite if you're in a hurry, but you'll sacrifice both working / re-positioning time and ultimate strength of bond.Some tips for you are: first clean and degrease your surfaces, making sure they are totally dry and dust free. If the surfaces are smooth, roughen them to provide a mechanical key if possible. Clamp the pieces together tightly whilst the resin sets and avoid the temptation to fiddle with them until the resin is completely cured. Wear gloves to keep this stuff off your skin - it can cause contact dermatitis and is a bother to remove. If you need larger quantities of epoxy resin head for your nearest chandlers - boat builders use it by the gallon.

It's been my go-to epoxy for many years, it works perfectly every time and I can absolutely depend on it.It doesn't set quickly, so that makes it really good because it's not a race against time to get the glue where you need it before it goes off, or, to remove glue where its ended up in exactly the place that you definitely didn't;t need it!The syringe dispenser makes it really easy to use, when I first used araldite it was in separate tubes, which is ok, but it's far more messy and you have to ensure you dispense the same proportion of both parts, it comes with a stick to mix it, but I just use tea/coffee stirrers, you only need to mix it for 30 seconds and you can tell when it's mixed when you cannot see any streaks in the resin.I use my stirrer to apply the glue, in my pictures I filled a void in a 3D printed part, although the epoxy is quite a "stiff" glue, it will fill gaps as it levels itself, this allowed the epoxy to fill around my "joint" piece which connected both haves, I placed my part face down on glossy card.You need to clamp your pieces to hold everything in place while it sets, you definitely don't want it setting with pieces in the wrong place because they're not coming apart ever, I use some cheap clamps and they work great.You can see on the front that the epoxy levelled and filled in the tiny gaps, resulting in everything being bonded incredibly well, you would break the bits that weren't glued before you had anywhere near any issue with the glued section.I left it clamped for 8 hours, after which I removed the clamps and then let it sit overnight, the following morning it lifted straight from the glossy paper and revealed a very clean joint. As this part is going to be painted, I used a coarse grit sandpaper to gently and methodically work over the surface until it was level with the printed parts, at that point I worked up in various grits to 3000, after which the area where the joint and glue was smooth and flat and you are unable to feel any difference in the surface between the printed parts and this joint section, it's completely merged into the whole part.It really is one of the best glues around.

Used to fix the handle of a clay pot back on, left for 12 hours and seems to have help well.Main issue is it comes with only 2 applicator nozzles which only allow for a single use as the epoxy dries inside the applicator.

Follow the instructions and it will do a good job. Not sure what I used it for !But had some before and it works.

Far more wasteful than the3 ordinary and cheaper tube. If it's not the cap failing to reseal it's the whole lot solidifying after one or two uses or the syringes needing brute force to expel both parts .This is really not reusable as reusing it is so problematical it turns into another chore that you have to complete before you can do the one you wanted to do. Then the next job is to go out and buy some more to replace the unusable one you've already got.An expensive and inferior way of buying what used to be cheap.

No issues

This is solid. Good value for money and sticks very well

Plus points: the dispensing and mixing tube is great - last time I used 2 part araldite I remember mixing it on bits of carboard with match sticks - that's been consigned to history - the pack is great.Negative points:1 - despite the claims - it did not stick the plastic parts I bought it to stick, and I had thoroughly cleaned the parts with IPA before. I'll now need to try another adhesive of some sort.2 - there are only 2 mixing tubes so if you only use a little glue each time you could end up being left with a lot of adhesive in the tubes and then needing to mix together on a piece of card with a matchstickSo a bit disappointed to be honest

Il est extremement étrange de constater que des Landes aux ardennes , de la Bretagne à la frontière Italienne , cette colle n'est trouvable nulle part ! que cela soit des enseignes spécialisées comme casto. , Leroy M. , ou n'importe quelle autre d'ailleurs , en passant par des grandes surfaces comme auchan , carefour ou encore Leclerc pour ne citer qu'elles , cette extraordinaire colle n'est trouvable absolument nulle part...il y a une trentaine d'année ce n'était pas le cas !en revanche vous trouverez sans problème des produits n'ayant de colle que le nom et qui ne rivalise EN RIEN avec ARADLITE...combien de fois j'ai été décue par une marque qui a le culot de copier jusqu'au couleur et forme du tube en bi-produit avec des prétentions d'une demi page au dos ...evidement portant la mention epoxy , cette marque c'est sader pour ne pas la citer ...besoin urgent du simple plastique j'ai acheté la sader qui n'a PAS DU TOUT fait le boulot..; désolé les gars sader , ça n'adhère PAS DU TOUT...ARALDITE dans le domaine de la colle c'est comme Bugatti ou encore Rolls Royce dans le domaine de l'automobile et des moteurs ...J'ose à peine imaginer les dessous de table aux gérants de supermaché pour déréférencer ARALDITE...Jetez TOUTES vos colle , à la rigueur en gardant la super glue 3 (pas en gel) et acheter juste ARALDITE selon vos besoin couleurs BLEUE ou ROUGE , respectez bien les temps de séchage 12H minimum , 24 idéalement .Restez sur la classic , en tube rouge ou bleu , evitez la rapide.Merci de m'avoir lu et merci amazon de proposer cette colle unique.

J'ai recollé un vieux pot en terre cuite pour l'extérieur et cela tient très bien malgré le poids. Il faut juste appuyer à s'en faire mal aux doigts pour faire sortir les deux produits.

top, comme toujours avec cette marque !

Bricolages divers - je connais ce prd depuis des années.

La qualité araldite est toujours là . Dommage que cette colle soit difficile à trouver. a noter que les délais de livraison sont très long ( plus de 15 jours) et que les informations de suivi presque inexistantes. Le vendeur vous répond mais pour vous informer que le produit est en cours d'acheminement et qu'il faut attendre la date de livraison annoncée.