12 Pieces Brake Switch Stopper, Car Brake Light Switch Stopper Brake Switch Pad Automotive Clutch Pedal Stopper 90541-06036

They were a little too small for my 93 accord but a little electrical tape made it fit! Good quality for what you pay for.

I like that thanks to Google and YouTube videos found out this little thing “brake switch bumper pad” exists and was most likely the reason the brake/tail lights wouldn’t shut off on my 2009 Hyundai Santa Fe. Brake/tail lights would stay on even when vehicle was off.. had to disconnect battery to get brake/tail lights to turn off.First check ..gently shake the emergency brake and that it’s not stuck or partially engaged. Of course I wasn’t that lucky to find it was the cause and solution of why the brake/tail lights wouldn’t shut off even when car was not running.I’m a 50ish young female .. found out via Google then YouTube videos what the likely culprit was and how to replace it. Saw what this thing was supposed to look like and it was mentioned it would likely be found in pieces on the floor of the car below the brake pedal or in that area (scattered around in a million pieces) I went to check the floorboard .. lucky me had just shaken out the sand from floor-mat ..but I found every single tiny bit of this disc like thing (the one on my vehicle happened to be clear making it slightly more difficult to locate),but I did find every single tiny piece. A plastic washer like thing.. maybe once was rubber like material,but what I found were hard tiny plastic pieces. Never knew this “brake switch bumper pad” existed and had never heard the term before. It’s not something you know is on your vehicle until it’s not .. or disintegrates causing you notice that one of the very noticeable features of your vehicle isn’t working properly. ..I am a 5’2” 100lb female. I want to get things done quickly and cheap,but done right. Also not the type (if I have time) not to try figuring out how to do something myself. Curious why I bothered picking up each tiny crumb of this thing? These parts are not readily available in the local auto parts stores at least not for my 2009 Hyundai Santa Fe.. and/or not where I live. and that’s why I spent the time searching for the little tiny crumbs. Ordered this particular one from Amazon.. most likely because it was stated to fit my vehicle and shipped fastest. In the meantime I found my magnifying glass that I really wasn’t sure I owned,but thought I might have .. and got out the tweezers .. fit the tiny crumbles back together like a puzzle and used fast drying superglue. .. once dried I watched the YouTube video again.. used some real colorful language .. can’t see that particular spot (not in my vehicle anyway) don’t know how big guys/mechanics .. well,they most likely remove the dash or drivers side seat .. neither was something I was the least bit interested in doing.But.. Once I did the research into what might be causing brake/tail lights to stay on even when vehicle was turned offIt was actually easy to do yourself andto be honest the part that I found and glued back together has been in place for months at this point and functions just fine. I most likely won’t replace it with this purchase until it crumbles and falls out again ..and you could probably use any number of things to replace it temporarily. I considered one of those rubber furniture leg pads .. the non skid or non scratch things.. I think that would have worked temporarily while waiting on the proper replacement piece or glue it together like I did (that was an extremely frustrating process,but needed the use of my car and certainly didn’t want to put others in danger with non properly functioning brake/tail lights If I had taken the vehicle to the dealership or any mechanic I’m guessing it would have cost me significantly more than what it cost me in my time googling and watching YouTube videos and the price of this part. Even though I didn’t end up using the part .. I’m keeping it as it might be needed later.Do yourself a favor and buy one or twenty .. (they seem to only be sold everywhere in multiples of 10) but the price is nothing compared to the dealership or mechanic.

If your brake lights stay on and the cruise control does not work, there is a 99% chance that this plastic stopper is the culprit. When this plastic piece breaks, you'll notice the remnants on the carpet by your feet. The only problem is that you have to be on your back looking where the break switch meets the pedal. Push down on the pedal and insert the stopper in the the hole. If the switch is too close to the hole, even with the pedal pushed down, you may have to unplug the switch, loosen the top nut and unscrew the switch in order to give you more room. It takes about 15 minutes (if you are limber, lol). Oh, my vehicle is a 2003 Miata.

If you own a 2002 Nissan Maxima do not buy this product!!! It will not fit as described on the Amazon website. Also they expect me to drive 45 minutes to the nearest UPS store return it to them so that I can get my $6 back! What a wasting time. So now I have to eat the $6 thanks to Amazon's poor description. So buyer beware!

Honda Bracket hole for this stop is larger than the "barbed" retainer on this part. Will require some adhesive to keep in place. Hard plastic part - will resist oxidation...

Perfect fit for what it was intended for

Did not fit on 2002 Acura RSX Type S as Amazon said. The stem is too small for the hole on the brake pedal so it will fall out. I used some JB Weld to take up the slack. Also, I don't technically need 12 pieces so seemed like a waste.

These may not last quite as long as the 23 years the OEM part did... but it's dealing with such low forces that it probably will. It just presses a button when the brake pedal is up, that's it. A very simple part.It's a fairly easy fix on a 2001 Toyota Avalon, once the bottom dash panel is taken off to get more space. It goes in a hole on a metal piece that's 90 degrees to the pedal's lever.