Sparco Slider Seat Track Set

This item works well. I have nothing negative to say.

After lots of debate to go fixed position or adjustable I found these tracks to be best solution. The double lock feature is 2nd to none. It is imperative to buy high quality hardware & take very accurate measurements mounting brackets/seats & sliders ensuring everything is completely square & level. I found making a wood template helpful then mounting each piece measured & level one at a time helpful. I built an Exocet kit car with 17" Kirky seats and had lots of metal fabrication that also included a wider handle for adjusting these sliders. I believe they would be perfect fit with oem seats or 15" wide. Make 100% sure you have everything in place before securing slider handle it is not made to come on & off. Handle also has a curve can be up or down as needed for clearance. I liked quality enough to put pass seat on slider too.

Fit my Sprint L seats perfectly and let them work with the Sparco adapter, unfortunately the Maxda MX-5 ND adapter and the Sprint L did not like each other. The seat was too wide and hit the seat belt mount. It also wasn't quite adjustable enough to fit in the car and the slider covered up the rear driver-most bolt hole so it had to be modified for me to even attempt installation. Good news was that once I shoe-horned it in the seat with sliders was still slightly lower seating position than factory and would have given me just enough room for my helmet. So, it's definitely work the money over the generic ones if you have a Sparco seat, but may not work in every application.

I used the Sparco Slider seat Track set to provide an adjustable base for the original Seat in my 1932 Ford five window coupe. It works perfectly in this application. I added a 1x2 inch rectangular spacer as a mounting base for each side of the slider set. I cut the release handle in the middle of the seat release handle to widen the pair of sliders to match the width of my 1932 seat mounting base. I added a straight length of tubing to reconnect the two supplied actuating/release mechanism that were left on each sliding base after cutting them in half. I also welded in another straight section the same diameter tubing connecting at each end to where the actuating handle takes off from its attachment bar. This second tubing section was added for stability of the handle during the actuation maneuver. It is a much better application than Henry's original seat adjuster. Now when I need to adjust my seat, I reach down and pull up on the release handle and scoot whichever way I want to go, and simply release the handle to allow both sliders to lock up.

These aee by no means universal, they come with no hardware, a dubious adjuster bar and just smell awful. These are coated in some factory oil that smells so awful it made me gag multiple times. It was like a rotten egg and metalic at the same time. The rails are greased, but only at the ends where the bolts go, so you get this thick rotten smelling snot on you just putting them together, while getting not really any lubrication on tbe actual sliding bits. I found that not only are they not universal in really any way, nor do they really seem to be attempting to be. I have recaro LX/LS seats and they aren't even remotely close. There's only four holes, and they're not oval'd out much, making the fit rely on luck of the draw. I'm glad I got no further than a test fit on these before I had the pleasure of returning them. I can't imagine putting these stinkers in my car.

It was advertised as next day arrival so i went and ordered 2 of these. It didn't arrive as listed. The install was easy and looks like the product would last for a while. No bolts are included which is a damn shame because at this price, it should've been. I guess they have to milk every cent where they can. Again, these sliders are okay, but I would recommend to look somewhere else if a friend asks me for advice if they should get this.

Great bracket that fits my seat perfectly, (R100). And I would buy it again. However, nothing against the bracket. But if you think spending 15 dollars for the mounting bolts is a good idea you need to learn how to manage money better. Go to Menards or to any home improvement store and buy the bolts there for 2 bucks.

Fit my Sparco Torino seats perfectly.