Bio Bidetby Bemis SlimEdge Dual Nozzle Bidet Attachment with Bemis Elongated Toilet Seat, Fresh Water Spray, Non Electric, Easy to Install, Brass Inlet and Internal Valve

1. Don't worry about the fact that the water is cold... You don't even notice. However, I live in Florida, so my cold water is never freezing - take that into consideration.2. Installation is pretty easy - took me 10 minutes. Yes, you will get leaks if you don't tighten everything correctly - be careful not to move/damage the parts inside the tank when you are tightening the fitting for the bidet.3. If you are under 200 pounds, this probably won't be an issue. One member of my household is rather large, and when sitting, overlaps the knob/bidet arm. I'm hoping it is well made enough to have taken this into account, and doesn't weaken the plastic.4. I know everyone is built a little differently, but the aim between the two settings (rear and female) doesn't seem to be different by much at all. You just have to adjust how you are sitting :)5. Turn the nozzle very slowly to avoid an unexpected enema! I can't turn down the pressure from the wall because it causes my pipes to knock..... So, just be careful!

Your browser does not support HTML5 video.  Super simple design, but packs a powerful punch!The install was easy - don't be afraid to get dirty if your bathroom isn't clean :-)Worth every penny and provides what toilet paper alone cannot.Definitely recommend :-)

One of these was bought as a test for the office. For the purposes of hygiene and personal interest of some of the staff. A test run to see how everyone likes it. So far, it looks like its a positive verdict mostly.1) Ease of install: The installation was pretty straight forward. You don't really need to worry much about the instructions as it is pretty straight forward. The only part we peaked at them for was to make sure the rubber washer was orientated properly. Beyond that, the seat sat flush along the front when we were done, thus never had to use the optional feet. Random note: always remember, never shy on the use of plumbers tape (the white Teflon tape) when it comes to water and anything with threads.2) Ease of use: Usage is pretty easy. Sit down, do your thing, and turn it on. One way for the backside, and the other direction for the front.3) Use impression: Most of the feedback typically fell into the category of "I did not expect that..." and "careful on the how far you turn it. The latter is more valid feedback than anything vs those that never used one of these before. There is plenty of pressure behind the water, so when you use it for the first time, you should slowly turn the knob to get adjusted to it and know where to stop. Don't crank it else you might get a surprise as the pressure can be a little much of you do. However, when you feel it out and find where the sweet spot is, it gets the job done quite well.The only thing that was unfortunate was the fact that it is far whiter than the rest of the "white" toilet. They should seriously (all of the companies) get together and come up with a consistent definition of what "white" means. So it does look a little funny installed sadly. Thankfully, it is about function before anything else. So we'll see how everyone feels in the long run.**If you have found our review helpful, please vote it as helpful below so we know. This helps us to provide quality feedback in the future.

I bought this item for my apartment (I'm on long-term assignment away from home) because the apartment doesn't have electrical outlets near the toilet to support a powered bidet, and the price was very reasonable. I have BB-1000 and BB-2000 in my house, and love both of them. Unfortunately, the BIo SlimEdge, even at the price, is not worth the value. It was fairly easy to install, but the location where the water jets point cannot be adjusted. Both jets spray to the front of the toilet seat, such that no matter how far one moves up on the seat, the water barely hits the correct target. In addition, even though the dial can rotate 90-degrees to the left or right to determine what jet is controlled (feminine or posterior), the degree of turning does not control the flow. The flow is either off or on full-flow, with full-flow being very extreme and splashing water all around the toilet. So, I'll be discarding this item and living without the benefits of a bidet while I'm in this apartment. If you have an electrical outlet near your toilet, I recommend the pricier BB2000; it's a great device.

This bidet kit was a pretty easy install, and I really appreciated the inclusion of teflon tape—no leaks whatsoever. I was pleasantly surprised the first time I used it and—without any kind of adjustments necessary—the unit scored a direct hit, right on my bulls-eye! My water is cold this time of year, but I found this chill to my Netherlands oddly refreshing.I did not give this unit five stars only because it is an economy, no-frills model. If you’re like me, though, that’s a good thing!

Toilet seat can't come down with this attached. See pictures attached. Water flow rate is much too high. This is going to be one giant mess even if I get the seat to work.Same fitting problem on a second Kohler toilet. I think the issue is with the downward curve towards the center on Kohler seats, hits the flat part just above the nozzle. You may have better luck if your seal is flat at the bottom.

Save yourself an emergency trip to Home Depot and buy a new toilet supply line before you install. Chances are that your old toilet supply line will leak when you first turn the water back on. Those lines don’t like to be disrupted and typically will not re-seal correctly after it’s been used over a year. Buy a “quick connect” supply line for the easiest installation - it’s specifications are in the picture I attached.The bidet itself is VERY white. So keep that in mind if you want it to perfectly match your toilet. The sprays are very accurate and both women and men can use this. Very good quality spray, but definitely not made of the strongest plastic so make sure you don’t try to support yourself on it when getting on and off the toilet.

Your browser does not support HTML5 video.  If ain’t got a bidet,I felt bad for you, son,Cause I got 99 problems,But a dirty butt ain’t one.This thing was super easy to install. I did it myself while my husband went for a walk. Everything you need is included in the package, including the Teflon tape and toilet seat bumpers. The adhesive on the bumpers failed within 24 hours, but I don’t actually find that I need them. If I change my mind I would find an alternative to stick them to the underside of the toilet seat.Anyway, install was easy and I had no leaks. To be certain I cut the cardboard box it came in into strips and put them on the tile around the toilet. That way I could easily see any leaks right away. I also used plastic wrap over the bowl to test the jets after I installed it. Feel free to steal that trick for yourself. You’re welcome.

Do not buy this if you live in Canada. We ordered it online and now it doesn't match the Canadian toilet standards. We have had hard time finding the exact extension it needs . So we wasted all the money.

Fácil de instalar, no se necesita más que una sola llave para instalación, leí una reseña que decía que las medidas no son compatibles para México pero creo lo está instalando mal, se debe instalar justo abajo de la caja de carga de agua.Espero mi comentario sirva para despejar dudas.

I snapped it up before the toilet paper craze, while it was still priced at 50$CAD. It's my first ever bidet and I am very happy I bought this. It mitigates my TP consumption while providing much better hygiene. No matter how bad your #2 was, you can get the entire job done and over with in one sitting/one flush/zero paper needed.I like the sleek and simple design/presentation. One button does it all. As a male, I haven't tried the "front" spray nor will I ever. The water jet is plenty powerful at level 1 (there are multiple degrees of power). The water is not heated but it gets to room temperature while it sits in the water line.Having this bidet was my way of trying out the bidet experience at low cost. I am now motivated to upgrade to a high-end Japanese model with all the bells and whistles. There is life before bidets and life after bidets. It's a whole new ball game. Trust me.

Es un problema para instalar ya que la llave que trae es de 7/8 hembra × 7/8 macho y una reducción de 3/8, y en México las llaves son de 1/2" y tienes que conseguir esa medida para poder instalar lo que es muy difícil