Lian LiGB 001 Graphic cardnhalterung Black

Works great and was super easy to install. I was concerned that it might not work with the B650 motherboard because of the heatsink, but the standoffs included are tall enough to let the whole bracket clear it!

I'm using this to prop up the MSI Ventus 3X RTX 4080 on a MSI MEG Z690 Unify-X motherboard. I was using the support arm that MSI gave me with the video card, didn't really look bad but was kind of a pain to install and didn't feel too sturdy. I thought I'd throw this in as added support for the underside of the card near the motherboard and use in conjunction with the support arm, but once I got it installed and had the card sitting perfectly level, I came to realize I really didn't need to use the support arm anymore, and this GB-001 support actually worked better overall. You can't even see the GB-001 support unless you're really looking for it, much nicer than the support arm that came with the card, or other "stand" options that are out in plain view.Big thanks to Greg Salazar on YouTube, he did a quick video about this item, I never would've known it existed had I not seen his video. Just wish it was a little cheaper, considering what it is, but it was worth it for me nonetheless. I bought a couple more of them just to have on hand if needed.UPDATE 6/11/25: With the same motherboard, this support DOES NOT work with the MSI Ventus 3X RTX 5080 - This card is interestingly quite a bit smaller and lighter than the Ventus RTX 4080. The padded support tab the card rests on hangs over the fan shroud too far and the fans aren't recessed into the shroud at all, so the support tab makes direct contact with the fan. Thankfully, this card is lightweight enough that I didn't really feel the need to use a support anyway.However, I can confirm this support DOES work quite well on this motherboard with the MSI Ventus 3X RTX 5090. This card is comparatively sized against the Ventus RTX 4080, therefore quite a bit bigger/wider than the Ventus RTX 5080, and the fans are recessed into the shroud a little as well, so this support is a perfect fit against the shroud and doesn't even come close to interfering with the fans.

Works great! There another review stating it does nothing but they have it installed the wrong side of their motherboard! It goes near the front of the case. My 7800xt only has an inch or so overhang past the support but I jiggled the thing around and it's super solid!! Works great as long as it's used right!

Really cool idea to utilize the motherboard standoffs to provide support for the GPU. There are a couple things to keep in mind, however:1. This will not be compatible with all motherboards. If the motherboard you're using has a large heatsink for the chipset, this will not fit. If you have any connectors between the two standoffs (USB headers, fan headers, SATA connectors, etc.) this bracket might interfere with these.2. This should be compatible with MOST GPUs, but might require some slight modding. The rubber pad that holds the GPU in place was actually touching one of my fans when it spun. My computer made a loud noise when I first turned it on after installation, I had to cut the rubber pad in half to solve this issue. Luckily Lian Li provides extra rubber pads and screws.3. Lastly, this works best with motherboards that have their GPU slot NOT at the very top. My motherboard (MSI B350 tomahawk) has a PCIE x1 slot ABOVE the PCIE x16 slot where you plug the GPU into. This bracket works best on motherboards with a similar setup, if your GPU is at the very top then clearance might be a little tight and you can't put a bracket above the GPU, only below it. I have one bracket above the GPU and one below, this was the main reason I wanted this particular bracket. So I could have support from above and below.Overall, great job Lian Li, this is a pretty innovative product if you ask me. Now I can travel with my PC in the car without worrying about the GPU snapping off when I go over bumps. Just make sure your PC is compatible before buying.

Does not fit a MSI Tomahawk MAG mobo, the heat shields will prevent it from securing to the mobo. It is very well made otherwise.

I was looking for a solution to remedy my GPU’s sag but everything on the market is just those hideous brackets/supports or ugly stands. Nothing low profile, no innovation, all the same garbage that looks terrible.However, when I found this, I decided to keep my eye on it for a while (when I first discovered this Lian Li sag support, it was not available on Amazon and only from Microcenter). The other day I found it available on here and bit the bullet.Installation was quite easy, but it did not fit where they tell you to install it (near the PCIE slot) due to my motherboard’s heatsinks. However, what they fail to really advertise/mention is that you can just install it over your sata ports on the rightmost side of your motherboard as well, which is ironically better as it provides more support to the end of the card where it’s actually sagging.Then, I ran into the problem of the support interfering with my GPU’s fan, as the L shaped bracket that screws in was slightly too long and passed my GPU’s shroud and went into the fans. Luckily, Lian Li provides two extra rubber pads, so I took one, cut it in half, and placed it on the support, but farther back so it only pushed on the GPU shroud and didnt reach into the fans. Works flawlessly now.This is the best sag solution on the market right now, low profile, works well, and is the only thing on the market that is remotely innovative in this space. Only con is that $20 is a little pricey for something so simple, but nonetheless amazing product. 5/5 would recommend, if any of my friends ever need a sag solution, this is what I’m getting them