RUITOOL Japanese Pull Saw 10 Inch Double Edge Sided Hand Saw Ryoba SK5 Flexible Blade 10&18TPI Flush Cut Non-slip Plastic Handle Wood Saw for Woodworking Tools

Once again, I am impressed by the quality of Ruitool products. While I was confident that the saw blade would be very tough and sharp, (which it is), I did not expect to be impressed by the non-wooden handle. As it turned out, the handle appears to be very sturdy, and the dark gray rubber-like cover material is both attractive and easy to grip. As a bonus, the company also included a fancy metal screw knob as an alternative to the stock knob to attach the blade to the handle. Nice little touch! Thanks Ruitool! I will not hesitate to buy other products from this company. Note: I had to add that this saw performs very well. It cut hardwoods like red oak and walnut with ease. Pine lumber was like slicing through butter. The secret to smooth cutting is light pressure on the pull stroke; I had only one finger pressing downward. Remember also to begin a new cut by gently pushing the blade away from you at the far corner of the wood to be cut. I believe the ease with which it cuts will surprise you.

At the time I purchased this, this was the least expensive Japanese pull saw (of this size) that I could find. All I can say is sometimes you get *way* more than you pay for, and this was one of those times. If you haven't used a Japanese pull saw, before, stop reading and buy this. The two sides have different teeth, allowing you to accurately and easily cut through just about anything non-metal. It handles both soft and hard woods with ease (use the correct side, though). Getting a cut that's straight/in exactly the right place for joinery isn't trivial without the appropriate power tools and I don't have most of them -- if it can't be handled by a circular saw, I'm ripping out the hand saw. Cutting precisely and quickly with a hand-saw is ever so fun for a newby -- because normal hand saws rip through the product while pushing, they bend/bind and screw up the cut. Pull saws rip through the board on the way back which keeps the blade straight, on push, they glide/cutting minimally. Besides being easy to control for precision, it's very capable at ripping through tough woods. It's so good, in fact, that I use my various circular saws/mitre/table saw about half as much. The circular saw will *cut* the board much faster, however, if I want a perfect/near-perfect cut, I have to set up a guide of some kind, clamp the crap out of things, and *then* cut. This saw won't rip through the board in one stroke, but I can lean on the board and cut a straight line with it without a guide, I can see if I'm drifting at each stroke and adjust accordingly -- at worst, if I'm in a hurry and free-handing it, I can hit it with some sand-paper afterward to clean up the problems. Basically, the choice is to carry a heavy circular saw, carpenters square, and a couple of vices to the work piece, set it all up, double check that it's lining up right and *then* cut the board or carry this extremely light saw and start cutting on the line. It's almost always less work to use this saw and it's a lot easier. ...and despite all of that, *it's still sharp after 6 months of use 2-3 times a week*. I wouldn't attempt sharpening this saw, myself; especially the side with the smaller teeth. I assume I can take this where I take my other saws/knives to be professionally sharpened, but I haven't had the need, yet. Part of this is because it doesn't bind, you don't start doing short strokes to unbind the saw so you don't end up with a blade that is sharp at the end and dull near the handle. The whole blade is wearing evenly. What's crazy, though, is that I'd swear this thing hasn't dulled at all -- It's absolutely *not possible*; there's no way this blade is cutting as well as it did when I purchased it with the amount of use it's had, but it cut through a large pantry project last weekend and it sure felt like it was brand new.

Well made, works very well for both fine woodworking as well as carpentry work. I have traveled the country and I always tell my wife I am bringing my small carpenter's bag with me. That small bag of essential tools and a cordless drill/driver have traveled the country as we have visited friends and family and without exception we have done very small, and more in a few cases, repairs or projects at our stops. You don’t need a lot but the Japanese double sided hand saw is an essential tool and this is very nice and affordable. 5 stars!

Cut off sacrificial face plate material from finished wooden bowl from lathe And cutting dovetail joints

If you've never used a Japanese pull saw before you will be amazed at the precision and razor thin cuts produced by the thin, flexible blade. This is great for all kinds of wood or plastics, and this Ruitool brand pull saw is large enough to handle big projects and fine woodworking. The handle has a soft rubber coating over tough plastic for a firm grip. The locking knob securely grips the blade but lets you easily separate the two. When finished, make sure you replace the clear plastic covers over the teeth to avoid rust and cuts; I accidentally brushed against one blade and got a small cut. It's just that sharp! I also suggest giving the blade a swipe of WD-40 or fine oil to keep your blade clean and rust free. Regular push saws are ideal for powering though logs and boards, but if you are doing woodworking or home improvement stuff, a Japanese pull saw is the way to quickly make those fine cuts for professional-looking results. Five stars.

Great saw for starting out as a beginner.

Cuts nice. Takes a little getting use to but it is a nice saw

Cuts fast and clean in hardwoods like oak. Good value.