EZARC Carbide Multi Tool Blades for Hardened Metal and Nails, 3-Pack

I did not stumble on these. They were a choice made after extensive reading up on what I needed to cut through some stubborn hardened nails. I was trying to remove the vertical frame of a garden fence panel that was nailed to the main posts - and to do so carefully as I needed to repair a section of it and put it back. I tried prising with all sorts of tools and angles to try and get enough purchase with a claw hammer so I could pull the nails out - no joy! Any harder and I was simply going to split the wood. The nails didn't budge at all. I decided to bring out the big guns in the form of my Milwaukee Cordless 18V oscillating Multi-tool with a view to simply cut through the nails through the joint between the frame and the post. I fitted my Smart brand plunge cutting blade for metal and went for it. In no time at all, the blade was completely blunted and the nail was still intact with little more than a scratch. I was very confident my Oscillating Multi-tool was more than capable so focus was on the blade. I did some online reading and quickly came to the conclusion I needed some Carbide tipped blades for hardened nails. Further review of comparisons of various blades on Youtube convinced me EZARC was the way to go here and the 3 pack pricing made this decision a no brainer. Availability on Prime was simply the icing on the cake. And so the moment of truth. I got my blades on the due date but somewhat late afternoon/early evening so out of regard for my neighbours postponed my rematch with the fence until the next day. Judgment day, and out came the Multi-tool once more, new blade fitted, and I stepped outside to face my foe. We are talking roughly 6 seconds to cut through the first nail - and that was me being cautious, expecting the same blunting I saw with my Smart brand blades. It was same again for the second and the third nail. I checked the blade after each on of these cuts and it was as if I hadn't done anything! No blunting observed! I turned to the other post and was done in a matter of seconds. Within 5 minutes of my stepping out the door, I had the fence panel flat on the ground ready for the repair work to begin. I was so very impressed with these blades that I decided to share this review on Amazon pretty much straight away! Indeed, I am only part way through the repairs as I write but that is for other reasons. Summary? Sure: Pros: Sharp, heavy duty, cut through hardened nails easily, well priced, well reviewed brand Cons: None Verdict: If these sound like what you are looking for, they probably ARE what you are looking for. No regrets to be had here; you're onto a winner! A+++

The best multi-tool blades for cutting metal bar none. I do not know how they do it, but these blades are amazing; massively better then any others I have used. I am repairing an old house & have to cut lots of old nails, screws & other metal fixings so as not to damage the wood/stone they are attached to: I went through blade after blade, trying all the big names but none would cut more than a few iron nails. These babies, however, cut through them like butter. I came across them on a USA video review of multi-tool blades, which they won easily. I was a tad sceptical (maybe the reviewer works for EZARC) but, when they arrived, I was very surprised at how brilliant they actually are at cutting iron, steel & even stainless steel. I should not gush about a simple blade, but they are that good. I do not know how they are so much better than the competition; but they really are. Do not hesitate; buy them.

A set of cheap cutters that can be used on hardened screw and bolts. This has cut through 6, 4mm screws quickly and without issue. There appears to be an edge on the blade still. Use with a slow spread, allowing the edge to cool by removing pressure occasionally.

These are the only blades that will cut though my summer house . So glad I got these . Other blades I tried were blunt in seconds

Definitely thought twice about the cost of these but after the bolts I were cutting melted my DIY shop bought blades took the plunge ... Good Decision

so got to use these yesterday, to cut around 3mm thick fibreglass, to replace stringers on my boat project. each stringer base has a footprint of 500mm long and a width of 50mm so in total I'm cutting around 1100mm for each stringer. I got onto my first stringer, thought great they are cutting well and with ease. got to my third one and bam the bit snapped at the joint. so not massively impressed with around 60mins of use the first bit breaks, luckily i got 3 in the pack so moved on to the next one and luckily it still going! managed to cut for a few hours having breaks in between. roughly got another 5 stringers cut. so quality is mixed, i didn't notice any deviation on cutting ability unlike to standard cutting bits the came with my multitool which in around 20mins of cutting was missing teeth and didn't cut as well. so yes the cut well but build quality is something to be questioned.

These fit my Ryobi tool just fine and do a good job of cutting through the rusty fasteners on my Defender.

I tried to cut 5mm from the bottom of the bolt in the photo, you can see from the photo it hardly touched the bolt but totally ruined the teeth on the cutting blade. I hope the company reads this and offers a refund. These were supposed to be 30x longer lasting and for the price I paid I was expecting a whole lot better performance.

Funzionano benissimo!

The first blade I used cut through copper pipe quite well but after third pipe it separated at the spot welds. Quite disappointed considering the price and expectations.

muy buenas. me estan durando mucho. Mejores que las de la marca dwalt que compre antes y mas baratas

Used it to cut some stainless steel piping, and it managed to get the job done efficiently without killing the teeth, which was a problem for bi-metal blades

Tres bon résistance mais un peu cher