NEBO iPROTEC LG Universal Long Gun Mount Black

worked perfectlyput it right on my mossberg maverick 88's magazine tube so I can actuate the momentary tail cap with my thumb !Goes on fast! quality productActually looks really cool too ! it is smaller then what it looks like onlineBut it's just right! has rubber inside so it dosent scratch the finish on your gun !since there is rubber it has a tiny wee bit of wiggle but that's the rubber flexing not the mount moving but dose not and WILL NOT A rotate or change positions in any way shape or form it's staying on until you take it off !Like other people said I was nervous about the plastic lock nut thing !But after I received it and put it on my gun I thought to my self the only way your breaking it is if youuse a wrench on the thing ! And lock the screw down with a hammer!Unless there was a manufacturing flawI have a no clueI got mine tight as I could and wrapped a rag on my hand to get it tighter I was able to tighten it that much for example in case your concerned..which i would not beBut mines perfect and I'm 100% pleasedI would buy this again and againWorked perfectly for my home defense shotgun love this little thing !I haven't shot the gun yet ! But I think it will hold up fine to 00 buck ! And slug recoil no problem I'll update as soon as I test !also has a small section of rail on it ! for any thing you may also want to hold on to your gun with the mount !***UPDATE****Held up just fine to the recoil of 00buck in my 12 gaHowever I had to take the Barrel off of my shotgun and to do that I had to take the mount off to allow access to the Barrel nutWhen I put the mount back on I got it a little too tight and stripped the screw out .. Sigh I ordered another one immediately because I do like this product a lot my dumb @$$ just got a little to OCD and over tightened it ..I'm gunna stop at the hardware store an see if I can get the long boltAnd the nut it screws into .. at the hardware store .. and see if I can get the bolt and the nut it screws into .. in the mount as I was able to remove them from the mount components ..I'll check backHopefully I can get another bolt/nut and fix this with harder steel hardware.. not saying it's a bad product just user error.. coupled with a little OCD lol !But if not a new one is on the way .for now my shotgun sits without its light:/ unfortunately. Hopefully I won't need it .****2ND UPDATE***Managed to get the bolt and nut at the hardware store and get it all back together and even tighter .. with harder steel hardware..worked good still have another mount on the way looks like one of my rifles is getting a light too haha 😂I'm happy again and my shotgun has its light back we're both happy lol

Bought this light mount from Fradon Lock Company on Amazon. Item shipped the same day I ordered it! Wow - fast! This light mount is well made of black anodized heavy aluminum with a "no tools required" quick attach/detach locking clamp. The inside of both sets of jaws are lined with molded rubber pieces resulting in a firm, non-slip grip once locked down. Two notes here - once clamped down, you will need to put something under the clamp handle to lift it to unlock it. I ran a piece of paracord under the clamp handle to pop it back open without scratching the mount or the gun. Second - I would not attach this to a barrel, as the rubber inserts might be negatively affected by a hot barrel. One side of the clamp has reliefs cut into the outside of the jaws, so it can fit between a shotgun barrel and magazine tube for a side mounted light. However, it would not fit sideways on the 12ga. Pardner Pump. Instead, I installed it at 6 o'clock under the magazine tube. The most it can be rotated up from the 6 o'clock position is about 45 degrees (let's say to a 4 o'clock or 8 o'clock position) then the jaws get wedged between the barrel and magazine tube. Once you lock it down though, it is SECURE. I used it to mount a 1" diameter Cree LED light to a shotgun and it is great. I can literally pick up the gun by this mount or by the light and swing it to my shoulder with no movement of the light or the mount. It is easy to use and SOLID! Great piece of kit - you won't regret this purchase.

I ranked the Nebo 5598 "okay" for a few reasons. I'd probably give it 3.5 stars if I could, but closer to 3.Update. I guess people have decided to mark my review as unhelpful? Here's the short version of the review. This mount will mount your flashlight and that's it. Don't expect anything sturdy like a permanent mount. My flashlight won't come off, but this mount is by no means sturdy. So if you want to mark the review as "unhelpful" go ahead, but I'm not taking my review back. The mount simply isn't sturdy. It mounts but it is very loose and I feel like any tighter and I will break the mount.Original review.While it definitely "mounts" the Nebo 5077 (although for some reason after my purchase, 5077's are nowhere to be found??) and is a perfect fit for both the tac light and my Moss 88 tube, I have a few concerns.First some good stuff. Only took 30 seconds to install. Very light weight but VERY tough exterior and comfy rubber interior. The foot print doesn't mess up the sling because you can adjust the mount like 35 degrees to the left and you're good. Secures your light enough to where nothing will come off on it's own. Fits Nebo 5077 perfectly. Also, Nebo 5077's are awesome (if you can find one..), impossibly affordable with amazing quality. Anyway moving on.Some sadly kind of stuff that didn't quite meet my probably weird expectations.I feel like there is a disparity between the ability for this to mount, and mount securely. It can mount, don't get me wrong. And it won't fall off, but anything past that leaves me curious. Basically this won't turn your tac light into any kind of breach tool, "DNA remover," or impromptu cover gripping mechanism as secure like a truly fixed mount would.I didn't even want to fully tighten it as I was afraid any tighter and it was going to strip out the threads. Whether it would or not I don't know but I wasn't going to tighten it anymore than it comfortably wanted to go. As tight as it would go it is loose enough to move around by hand axially, but tight enough to not move on it's own laterally. Any pressure whatsoever though will flex it about 35 degrees laterally.Here's the thing though. It did mount my Nebo 5077 so I'm not mad at it. It didn't meet all of my expectations but usually my expectations are all messed up anyway. I now have an affordable, and surprisingly cost-effective tac light mounted secure enough to where it won't come off by itself.Bottom line. If you have absolutely NOTHING, and don't know what to do. Get yourself a Nebo 5598 mount and a Nebo 5077 tac light and then worry about the rest later.Edit. I had to bump my score up. This mount held together when my heat shield came off (needs thermal tape), and my sling reflex bounced itself off (needed to be attached in reverse), and my tube started unscrewing (needs lock-tight). So this thing absolutely secures my light to my tube and the locking mechanism is just fine, although I have it super tight to the point to where I'm worried it'll break, strip itself, or crush the tube (heh) but it's held no problem so that's probably how tight it's supposed to be. Granted again I don't retract my statement that it isn't as secure as a production job. You can't use this as a defense tool or to brace against a surface. It's *only* for mounting your flashlight.Also mount it at a 45 degree angle clockwise or the recoil will bump it into your knuckles.Anyway this's all a learning experience, so take care and hollar if you have questions.

I bought this as a replacement for my other one that crapped out on me. Make sure that when you are tightening and loosening it that the lever is in the unlocked position otherwise the screw will strip and it won't tighten. But that aside it's honestly a really good and cheap gun light mount.