RP Remarkable Power, Fog Lights for 2013 2014 2015 Altima Chrome Black Bezel Kit with Wiring Harness& Switch Clear Lens FL7118

Installed on 2014 Altima S. Install took around 1.5 hours and a majority of that was cable management. Thought I would provide a basic guideline for anyone that may be considering this product to what is involved in install as there are no instructions provided with this product.First examine the package and ensure that you have all the parts before beginning. 2 fog lights, 2 bezels, bolt hardware (4 bolts 4 chimney nuts), wiring harness and switch.I removed the air box and air dam, (flathead screw driver and 10mm socket w/extension. Removing this gives better access to the firewall cable grommet to run the harness through to the cabin. There is a breather hose attached to the airbox that can removed if needed, it can simply flip to the side and rest on the engine without removing the hose.Thank Nissan for tucking the grommet behind the strut tower. The firewall wiring grommet has 2 molded sides, engine side and cabin side. I made a small incision on both sides to feed the wire through. Pull the wire through about 3 feet to give you enough room to snake around existing under dash wiring. I went back after and sealed around the incisions.The loose red cable that comes off the switch plug is for ignition power. There are a few options for connecting this but for those who aren't familiar tapping off directly off a wire(or know what wire to tap off of), you can choose to carefully pair this wire into the corresponding fuse and plug back into the fuse box together.The switch fits into one of the empty slots next to the hood pop. Be cautious when removing the empty spacer (it just pops out) and you can scratch the dash.The remainder of the cabling under the hood- red to battery, black to ground. I secured the relay to one of the bolts for the air box mount and looped the excess cable with zip ties.Route the cables to the fog lights to match the existing wiring harness and secure with zip ties.The fog light hardware is relatively simple to install, pop out your existing bezels, slide the chimney nuts into place on the new fog light brackets (I had to drill out the holes slightly on the fog light brackets as they didn't completely line up with the nuts) push the fog light into the hole and connect to the plug. There are a few tabs on the fog light that correspond with slits in the bumper for placement. Bolt the light into place and pop in the new bezel carefully. There is an adjustment screw on the bottom of the fogs to adjust position after install.I used my own zip ties as they were black and better quality that the ones that are included. My only minor dislikes is that the switch feels rather cheap, it doesn't really seem to have a solid 'click', but works just fine, also the led light in the switch is green.All in all this is a great kit and would recommend.

I was skeptical about buying this fog light kit, but once I carefully inspected the contents of the box I knew it was a great deal. If you purchase 1 fog light housing (glass part only, Left or right) from an auto parts retailer online or in store it'll be at least $40 alone. So at $42.99 (price I paid for it) here, it's a steal. Fog lights are adjustable, comes with all needed hardware, fuse, fuse holder, h11 connectors, fog light housings, 2 h11 55w fog light bulbs, fog light bezels, rocker panel switch, relay, wire loom, wire protector (semi hard plastic over wires). Install is pretty much routing the wires (all wires already close if not exactly cut to what is needed in length) then plug and play. It works great. Had to adjust the beam using a #2 phillips screwdriver (can also turn with fingers if it's loosened already). Beam was too low @ 1st. - The only way that this kit could be better is: 1.) If the wire was pure copper instead of a silver colored conductor. .2) The fuse holder was water proof (I just bought my own and swapped it). 3.) Rocker panel switch is Nissan's orange matching, instead of an orangish yellow. 4.) No fog inside the fog lights at all (getting very minor fog around edges of the inside of fog light, not sure if it's normal....not an issue though so far) 5.) Also, the glass fog light & the plastic bezel has a small gap (not there in a factory installed kit), it should fit firm (not loose at the moment though) 6.) Wish this kit simply had h11 connectors that plug into the OEM fog light connectors (already pre-installed from Nissan (just plugged up), even though mine didn't come w/fog lights) & also, a turn signal switch w/fog light option (O.E.M. equipment allows for a replacement of a non fog light turn signal switch to be swapped with a fog light turn signal switch...I believe). Overall a great kit. I have another Nissan altima (2015 Altima S, just like this 1) & would definitely buy this kit again for that 1. Great deal. Quality parts, a steal for the $, no major issues, my complaints are minor....5 Stars.

Fit like factory. Easy install harness with factory style switch. Makes a huge difference on the road at night. 3 months in and still doing great

These are just like the factory i recommend you buys these

De muy buena calidad, lo malo no trae unas minimas instrucciones, y el cable que se conecta a la luz es muy corto tuve que poner otro aparte, pero por lo de mas muy bien ya estan instaladas, mucho mejor que unas que compre en ebay, casi por el mismo precio

The difference this made on my car was amazing I can actually see in the dark now.

If you have an Altima without fog lights, you surely know night driving can be a pain. These work great and installed very easy. Very bright and well built all around.

My flood lights were damaged in a minor front end collision. This kit had everything I needed to completely replace them and get my flood lights working again. I live in east TN, so fog in the early morning and late at night is an issue. It's so good to have functioning flood lights again.