bayite DC 6.5-100V 0-100A LCD Display Digital Current Voltage Power Energy Meter Multimeter Ammeter Voltmeter with 100A Current Shunt

The bayite DC 6.5–100V 0–100A LCD Power Meter is a fantastic tool for anyone working with DC circuits, especially in solar, battery, or off-grid setups. I installed it in my camper van to monitor battery performance, and it’s been incredibly accurate and responsive. The LCD display is crisp and easy to read, even in low light, showing voltage, current, power, and energy all at once. I appreciate the real-time feedback—it helps me catch inefficiencies and optimize usage. Installation was straightforward, and the unit feels well-built for long-term use. For the price, it delivers professional-grade insight into your power flow.

Almost three years ago to the day I bought this and it's still working well in my system. It was a little confusing how to program it at first but once you learn it, it's easy. Best $16 I've ever spent, I highly recommend it.

This provides me good information but the display is not visible unless you look from directly in front, even with the light.

I purchased two of these bayite DC 6.5-100V 0-100A LCD Display Digital Current Voltage Power Energy Meter Multimeter Ammeter Voltmeter with 100A Current Shunt and installed them in my motorhome a month ago. I wired them so that one meter shows all current flowing out of the house batteries and the other shows all current flowing into the house batteries. I only needed to use one amp meter shunt at the negative terminal of my battery bank output to accomplish this. This arrangement has worked exceedingly well for me. Both meters show the identical voltage readings. With these meters I can keep easy tabs on what my electrical system is doing. I can tell what the current draw is for the various loads that I have (lights, water pump, standard dorm fridge, etc.) and the watt-hour meter lets me know how much my battery has been depleted (if you know the total capacity of your battery). It also lets me see what my battery charger is doing with regards to voltage and current delivery. The illuminated display uses hardly any current (3 milliamps) so I keep the light on all the time. It makes a great night light. So far both meters have worked great and were relatively easy to install. I can't believe I waited so long to install something like this. It's so inexpensive yet so helpful. A no-brainer. EDIT 7/13/2018 - Meters are still working great and are very helpful. This should have been standard equipment. I added a photo showing how I cut out mounting holes for the two meters in a standard light switch plate and mounted this plate over a cutout on the interior cabinet wall.

I have been using these bayite meters for almost three years now, not only in my travel trailer, but in my shed solar setup. The CHARGE and DISCHARGE meters in my photos are my original meters purchased in April 2019 and the SOLAR and INVERTER meters are the newer models ordered in April 2022. The only differences I can discern is the button on the front. The older meters had a recessed button and you needed a pen or pin to press it, whereas the newer model has a low profile button but can easily be pressed with just a finger, no device needed. The picture attached is before I upgraded the system: 10A controller with 200W solar array (upgrading to a 30A and 300W next) and these pictures were taken under partial tree shade in the late afternoon sun. The TT is running a 2000W modified sine wave inverter off a 385AH flooded lead acid battery bank, which powers mostly a residential mini fridge in the TT outside kitchen, wired through a 120V manual transfer switch to the GFCI outlets. You can see that the INVERTER load from the fridge is about 6A, while the solar output is about 4A, which correlates to the almost 2A battery discharge (including other low current devices: RV fridge circuit board, USB outlets, display lights). This type of setup is great for monitoring and measuring the performance of your batteries and solar system and if you have enough solar available or if your inverter loads are too much. To see what your actual amp-hour draw is, divide the ENERGY output by 12 (or whatever voltage you are running) to get AH so you can size your battery bank appropriately. My setup needs about 186 AH max per day and I am adequate on capacity but really should add an additional 100AH (of course I should add an additional 100W of solar too, but really there isn’t a hard ceiling to the max specs, just mind your budget). I boondock occasionally, but consider myself more of a touring adventurer, meaning I drive long distances in between destinations and camp mainly overnight in the forest or dispersed. My tow vehicle provides charging power along with the solar panels to recharge my batteries and my last 24 hours yielded 166 AH used so I never get below 50% of my battery bank. The extra 100W will help with the charge too once complete. I 3D printed a couple of meter mounts in black ABS and mounted them outside of the RV’s control panel. I could have also flush mounted them for a lower profile look but I think they look pretty good the way they are now. I used some spare Cat 6 and some jacketed landscape wiring to run from the RV batteries to the control panel. I would recommend finding some type of stranded small gauge wire for ease of crimping onto ring terminals and heat shrink tubing to protect them from separating while attached. Using ring terminals is the most secure to attach to the shunts but you can use spades or bare wire too. A good option for mounting is directly attaching the shunt to the negative battery terminal or inverter post, just remember to attach ALL load negatives on the other side of the shunt to accurately capture all discharging loads on the meter. The diagram provided by bayite on this site in the manufacturer pictures show to connect the solar meter/shunt AFTER the controller, which is a correct installation if you want to know how much power the solar controller is sending to your batteries. Bayite also provides a link to a modified diagram where the solar meter/shunt (included in my review pictures) is connected BEFORE the solar controller, directly in line from the solar panels, which will provide the meter with information with how much power your solar panels are actually producing. Each wiring is correct but provides different information; the voltages will differ as connecting before the controller will show the solar panel voltage whereas connecting after will show the battery voltage. Your shunt may have cuts in them, which is completely normal as it’s how they’re calibrated. Other reviews here say they have cuts and that they are damaged, but that’s inaccurate. These meters are good displays especially for solar controllers that don’t have displays or don’t show enough information. Great product, great longevity, and great information displayed for nerd like me who like to watch the numbers go up and down as conditions change.

I like the information displayed, the clarity of the display and backlight that can be turned on/off. Plus it remembers that the display was on last and will turn it back on when power is restored. The accuracy is pretty dang close but is off from my measurements (close enough for me to call it 97% accurate). Also when it gets colder (approx 48 degrees Fahrenheit) the display goes glitchy like shown in the image for the whole day. I don't think that is very cold but take it for what it is. I have just ordered my fourth. But one of my three has failed simply by unplugging a 12V battery and plugging it back in. So know that they can be a little sensitive too and its only been 45 days since I've owned it. So would I purchase this again? Well, I just mentioned I ordered my fourth but only did so because the price got low enough for Christmas. If it fails again I will scream and change my review to one star.

Excellent

It does what is set to do: tells you the state of your battery bank. Very accurate and easy to wire. Recommended.

I am using 4 of these meters to monitor my solar battery system: - Battery in - Battery out - Inverter out and - Charge controller out Installation: I found it them easy to use and install. Acuracy: I am very happy with it's performance and acuracy, I've tested it against other meters, charge controller displays and multimeters. Support: I had to contact their customer service as there was some confusion (created by me) and they were super helpful. Usage environment: I am using this with a 24V battery system (Voltax), a Epever 200W inverter and 1200W of Canadian Solar panels. You can see them in action on my EcoAmbitionsAustralia YouTube channel in more detail.

No complaints. Invaluable to a novice to evaluate parasitic current draw.

A tiempo y cumple su proposito

very good small monitoring center to track the battery charge and discharge.