Partsam Rectangular Red LED RV Camper Trailer Stop Turn Brake Tail Lights White License Plate Light 49 LED with License Bracket Holder and White Base 12V Sealed w Reflex Surface Mount (Left + Right)

The stock tail/brake light fixture on my popup tent trailer started to fail intermittently. Banging on it was a solution, until I cracked the plastic cover. Queue these LED replacements. Installation was super easy. Cut away the silicone on the trailer, remove the old light fixtures, replace the butyl tape, connect the wires to these lights instead, screw them in and they worked instantly. Tail lights, brakes lights, and one side comes with a bottom edge white light and mounts for the license plate. Brighter than the stock incandescent bulbs. Highly recommended.

Switched out the old 30 year tailights for these LED ones. Made a ton of difference and they are very bright. For the money, you can't go wrong. Just wished that they had reverse lights , but I knew that before buying. I would still highly recommend.

I installed these on a vintage SunLine camper that originally had those old rectangular tail lights. Vintage enthusiasts will probably hate to read this, but the very first thing I did was upgrade to these LEDs because the original factory ones were incredibly dull with corroded contacts, and only one of them worked.Measuring the size of my original tail lights, these were 'close enough' so I decided to go for it. Note: Basic wiring and sealant is required during install. They actually fit well as a modern upgrade, and are very bright even during the day. Its been almost a year now, and the lights show no signs of wear or discoloration. Great buy; no regrets.

First going to preface this with I have wrenched on cars, atvs, snowmobiles, and other trailers (except the one I put these on) for about 15 years now as well as have a few years in remodeling construction. They are great once you figure out the wiring. Bright, cheap, look good, and replaced the old broken lights on my 05 Keystone nicely. I have not seen any issues with condensation yet and Alaska eats aftermarket chrap lights alive. Bright enough I can see them light up through the smoked lens during the daytime and the license bulb is crazy bright (used for a vanity plate on mine). Will be buying again for sure if they go out. That's the good. The bad? GIVE ME THE WIRING DIAGRAM or label the wires. I had to swap 2 wires around on the non license plate light but otherwise wired right up with ease and was ready to go in probably 10 minutes.Getting the signal and black wire straight was my issue but a quick touch to a 12v battery's terminals let me know which wires did what

I bought these because the lense on my original light broke and I didn't want to deal with water intrusion. I was a little worried because these come with 3 wires and I only saw 2 on the original but once I removed the original, I saw the white one tucked behind. It's not hard to wire these together, even if you're not mechanically inclined. All you need is butt connectors and some heat shrink to cover the connectors. The only issue I had is that there's no diagram for which wire goes to where. The white goes with white, red to black, and black to green. Hopefully that helps someone else. I would definitely recommend these.

We replaced the rear lights on my 24-foot Coachman camper. We needed to replace the license plate holder, and this did the trick. The lights look very nice and are bright!

Wanted better visibility when braking for those following the trailer. The existing incandescent fixtures were dim in daylight. These installed easily and show up great, day and night. The units are a bit smaller than the old fixtures, but removing caulk/residue with goof-off worked well.

Very bright. Love it

These replacement LED’s really helped clean up the look of my old trailer and added brightness while traveling. Easy to install and didn’t break the bank

Tres belle qualitée pour remplacer les feux de ma roulotte neuve Salem qui arrive avec des feux cheap…les branchements ne correspondent pas mais après avoir essayer un peu ça fonctionne..😅 je vous joins les photos des branchements d’origine et ceux avec les LED .😊

fontionne parfaitement et s'installe directement au même endroit que les anciens avec ampoule conventionnel

White wire is the ground! And you need a stable 12v to make it work!Good product for the money but work fine! Look cheap but coolA1 it a good buy!

look good