[Patent] Muzata 80 Pack 1/8" Invisible Cable Railing Hardware Kit 40Pair Tensioner and Terminal for 2"x2" 4"x4" Wood Metal Post T316 Stainless Steel Deck Cable Railing System CR26

Fittings are top notch quality !!! Crimping them does damage to your hand. I would highly recommend the power crimper!!

Look great! Installation not easy (not complicated either), no issues (except on stairs). Not inexpensive - finished look is excellent. Issue on stairs was getting a proper length. No directions included and website/videos do not cover angular installation. The need for the installation tool and its robustness was my biggest issue. See tool review. The detail on this part that fits into the tool is not robust and tends to round over. Takes a lot of effort to hold in place while tightening the opposite end.

The product quality is really good. You’re stuck having to buy their tools to make it work which does suck. However, zero instructions come with it. After researching their products I finally found instructions and followed them to a tee. All the cables sag, I can’t tighten the end pieces any more than they are. I’m going to have to come up with a fix. My advice is don’t use the instructions you find. Mark the end of the cable where it comes out your post, pull it back out then measure 1.5” back mark and cut there. That’ll give you room for tightening. The instructions Muzata gives causes too much sag.

I used 4 x 4 steel tubing for the posts. The “tool” (I purchased separately), needed to be ground down to fit inside the holes. good product, clean look and design of the turnbuckles.

All the nice, nice videos don't really explain how to do this. Oh, sure, I managed to get this together after ruining one after another because your swag tool didn't really swag correctly. Oh I pumped and pushed and even put it against the street after the 4th swag slipped right out. I pealed back the vinyl coating and tried with and without the vinyl.Look at the '01/19/2019' picture, it looks ok, but if you touch it you can see/feel it is not tight. And now I've ended up putting two fence/sign post rails. I only needed 10 'lines' but I used 18 by the time I was done.See that Studio? I built the whole thing, so I am not a novice. They make it look easy, oh, clip here, squeeze there and viola, fence! Nope, test, trial, frustration, this should be easy right? Swag one end, put the other end and swag/screw it down. Here's a hint, if you only need 10 cables, get the 20 pack. Swag the first, pull them thru and check, double check, triple check, make your cut, swag your threaded piece and pray, sacrifice, whatever you need, and for cable #2, remove cable #1, swag the end for cable #2, pull cable #2 thru the last post cut a healthy overhang and then lay #1 & #2 down side by side (IF, and only IF, #1 fit so you could make it tight enough) then cut #2 cable a smidge shorter than #1, you will *probably be able to make that work.Now the bad news, like others here have said, as soon as it got hot here (85/90) this past week, two of my cables have become un swag'd, how is that possible? Just decided to droop then drop. Fell right out the hole.As you can see in my current (April 4th 2020) picture, I'm using a couple of green sign/fence posts to protect the studio now. You can see the droop. Maybe in the future I'll look into some turnbuckle thing but I doubt it, this was just so it didn't look like some cheap alley fence against my new studio, but unfortunately this particular method just isn't fit.I can not recommend this without lots of trial and error and again, you need 10 lines? Get the 20 pack A 30 pack would be a better choice and I don't recommend even trying until the hottest part of your season, and because the swag doesn't hold very well, they'll probably pop out when it's too tight so...

These are pretty nicely made and they were delivered quickly, which is a huge plus these days when you have a project. Muzata underplays the work involved though. I needed to add washers and use nickel anti seize. Crimps sometimes slipped using their crimper. Similar fittings available for less at online rigging stores

Really disappointed in this batch which I've purchased before. The cold heading tooling has obviously warn out as the socket head would not allow the socket wrench to fit. Ended up having to use a hammer to tap the wrench into most, making it difficult to remove, many I had to clear with a file or a dremel. Spent way to much time for what should have been simple. Also had several of the cable mounts split when crimping.

I could not find a video or any information about what size holes to drill for the system. I tried drilling the size holes to match the dimensions and the product information but they were too small. I had to go to a three-quarter inch Fostner bit for the indent. I had to go to a 7/16 inch bit for the shaft and I had to go to a three eights bit for the quarter inch cable so I could get the tool down inside at the post to tighten the cable. Otherwise the look is a 5 star.