MPA2019 3D Printer Adhesive Glue for Nylon Filaments - Long-Lasting and Reduces Warping on Flex Plate, Glass, PEI, Buildtak & Kapton - 3D Printing Accessories, Supplies, and Materials (50mL)

Got the magigoo for PC because I wanted to try printing polycarbonate, initially tried printing on my bare PEI bed and it was a complete no go. My bed only gets up to 110c and the PC was not sticking at all, literally just lifting off the plate super easily and prints failed during the first layer. Followed the directions for this magigoo and started my print, got absolutely fantastic adhesion and my print came out great! It was easy to remove from the cooled bed as well. I also did not clean my bed after applying this, it helped a subsequent PETG print stick very well and no issues removing that print from the bed.

This is for the Nylon glue. It is fantastic! I had previously tried every possible solution, the best out of them being a G10 sheet, however it still was not working 100% perfectly, still was having issues with large parts, or parts with sharp corners, or parts with greater infill. With this glue on a standard textured PEI sheet, the nylons stick extremely well! For any size of prints I have tried, and for those that I was not able to print with any other method. Even after cooling down the prints are attached firmly to the surface! I am very happy with this product!

This is my go to glue for printing PA6, PA12 and such. This always helps with bed adhesion as well as release. Since using this glue I have zero issues, I've previously destroyed a build plate with a different product, but this glue is amazing and makes printing with PA6, PA12 and other higher end material a breeze.

Fixed my adhesion problems immediately

The best adhesion is with the sheet that you stick on the print bed that comes with Yousu PP filament, but it is only good for one print, and it is hard to remove from the print ... but it has worked consistently. Magigoo PP definitely 'can' work, and often for multiple prints before re-applying, and Magigoo has been my favorite for bed adhesion for other difficult materials, but there is a learning curve in preparing each print to be successful with Magigoo and PP filament ... like very wide brims, etc.

When I first started 3D printing every print was impossible to remove from the bed. No matter what I did it stuck to the bed and I had to pry and pry to get it off. I started using this glue and it's made a huge huge difference. People suggest all kinds of weird things (like hairspray which makes a huge mess overtime) to get your prints to stick and come off after printing. This stuff goes on clean and easy, becomes a little tacky when the bed is warm, and holds the print well. After the print is done I let the bed cool down and the print comes right off. You have to put it on when the bed is cold, and remove the print when the bed is cold for it to work best. Be patient and it will work wonders. The bottle looks small and it might seem expensive for the size, but it will go far. I'm 1/3 of the way through the bottle after using it for a month. I've printed dozens of items in the time, covering the entire bed each time. Most of the time I remove it after a print with 70% isopropyl alcohol to get a nice clean bed before each print and reapply. The manufacturer does indicate you can use a single application for several prints, which I have confirmed is true. But I'm OCD about keeping my bed clean so I clean and reapply after most prints, and I still likely have 100 or more prints left worth of glue. If you're more frugal with it than I am then you'll definitely get more prints. Shake it well before each use. When you apply turn it upside down (obviously) with the sponge side on the plate. Push down gently as you move the bottle around to release the glue, and make a nice even thin layer of glue. Sometimes a quick push is all you need to get the sponge wet and then you can just rub the glue around until it's covered the area you need. The reason I mention this isn't to state the obvious, but the sponge does get some wear and tear on it after a while. Fortunately, the manufacturer realized this and there is an extra sponge that comes with it. If you're having problems with either adhesion or removal BUY THIS RIGHT NOW!!! Skip the cheap glues (5 sticks for $5 deals), the hairsprays, and the other weird tricks and just buy this.

Stuff is a life saver and for what little it costs compared to a failed 6 hour print it is value for the money. To put it on you just apply in the area you want putting lines down vertically then horizontally, that's it easy stuff. It keeps the materials firm to the base even with a less perfect level so it is plenty sticky. To clean the stuff just run it under some water and take a towel to it.

Ya me había cansado de que de buenas a primeras algunas piezas se desprendieran de la cama en plena impresión a pesar que siempre limpiaba la cama antes de una impresión y con las temperaturas específicas del fabricante del filamento para cama y cabezal y ni aún así. Ya con esto asunto arreglado, estoy muy satisfecho, mantiene muy bien adherida la primera capa de impresión incluso con filamento que me ha costado trabajo que se mantenga adherido a la cama.

Ich habe versucht Filament mit ähnlichen Eigenschaften wie PP zu drucken (Bavaria Faments, Olefin). Auf dem Bambulab war eine Haftung des Objekts weder mit der kalten, noch mit der texturierten Druckplatte zu erreichen. Mit der Hochtemperaturplatte und mit dem Klebestift gelang letztendlich eine ausreichende Druckbetthaftung unsaubere Druckergebnisse. Ich bin kein Freund von Klebestiften, 3-D, Lack oder Konstruktionen mit Klebeband, aber einige Materialien lassen sich nur schwer beherrschen. Mir fehlt der Vergleich zu anderen Klebestiften, aber mit diesem (doch recht teurem) Kleber hat mein Druck funktioniert. Ich werde daher dabei bleiben, wenn ich PP oder Olefin verarbeiten muss.

Ive got a couple of reels of esun ePA-CF. Its quite nice filament but it warps like anything. Its an absolute sod, peeling up after a couple of layers (60deg heated chamber, 100deg bed, brims, Hilbert first layer, slowed right down - tried everything) This stuff is expensive but it just works. No more warping, no more huge brims (depending on geometry). Very impressed with it so far.

Tut was es soll. Haftung gut

Después de haber intentado imprimir de 1000 maneras con Policarbonato, este ha sido el único producto con el que he podido hacer que la pieza se adhiera perfectamente a la base de impresión, ni con la típica laca nelly, 3dlac, dimafix, no había manera. El único punto en contra es el precio, por un botecito bastante pequeño el precio es bastante caro.