🚙 Elevate your Wrangler game with precision and ease!
The TeraFlex 1155110 Front Load Level Kit delivers a 0.5-inch front lift designed specifically for JL and JLU Wrangler models. It compensates for added weight from aftermarket accessories like bumpers and winches, maintaining optimal vehicle stance. Compatible with original or stock-length shocks, with Falcon shocks recommended for enhanced performance. Installation is straightforward, taking approximately 1.5 hours, and the kit includes all necessary hardware for a hassle-free upgrade.
| Brand | TeraFlex |
| Auto Part Position | Front |
| Material | Plastic |
| Included Components | 2 spacers^hardware^ Instructions |
| Maximum Lifting Height | 5 Inches |
| Manufacturer | TeraFlex |
| UPC | 843885046127 843995046123 |
| Global Trade Identification Number | 00843885046127, 00843995046123 |
| Automotive Fit Type | Vehicle Specific Fit |
| OEM Part Number | 1155110 |
| Model | TeraFlex 1155110 Front Load Level Kit, 1 Pack |
| Item Weight | 9.3 ounces |
| Product Dimensions | 5 x 6 x 7 inches |
| Item model number | 1155110 |
| Exterior | Plastic |
| Manufacturer Part Number | 1155110 |
R**S
Great Product and Support...!
Very good product, mounts just like any other leveling kit with a coil spring.I recently added a steel bumper and winch to my Jeep Gladiator, I then noticed a slight drop in the front end...so I ordered and installed these units. They did the trick and key off of the factory spring buckets and rubber isolaters, I know these are installed correctly and have restored the height from the extra weight.Thanks
R**R
Perfect and easy
Very easy to install. Makes the jeep look better.
D**E
Brought back that flat stance!
After adding a Warn EVO 12S winch, Warn winch plate and MORE Offroad engine/trans and transfer case skids to my new 2022 JLUR Xtreme Recon (with factory steel bumpers), the front end sagged about 1/2", and took on a nose-down stance I don't care for. These worked perfectly to restore a flat stance and ground clearance, and as others noted, did not impact ride quality. Measured before and after, and got the advertised 1/2 back up front!
N**S
Easy install, very nice look
I generally try not to weigh down the Jeep to much, and I was looking for more of a level look. These were exactly what I was looking for, and I wish I would have just installed them at the same time as the Mopar 2" lift.
A**M
Great for leveling
Wanted to be a bit more level than what the full lift kit provided so I pulled the right springs (front and back) and added small spacers. Apparently JTs frequently sag to the passenger side after lifts even with the more expensive fully made in America lifts (and somewhat from the factory). These did the trick and appear to be very well made.
F**N
Didn’t notice a difference?
I installed these because I added a winch and winch plate that added about 75 pounds to the front. I should have taken a measurement before I installed them but forgot. They took about 3 hours to install and I had a lift available, fairly straight forward. I didn’t notice any difference before and after visually but again I didn’t measure first. The ride quality didn’t change at all.
J**E
Great product!
The 1/2 inch spacer was exactly what I needed to bring the front of the Jeep up to level after installing a steel bumper and winch. Worked great and the install was not hard all you need is a jack,jack stands and some basic hand tools.
T**
Jeep jl wrangler level lift
If you have a 10,000 # winch, metal bumper and you are putting on dual rate springs, odds are you will need this to level out your jeep in the front after a spring lift.
ترست بايلوت
منذ شهر
منذ 3 أسابيع
