AOQEE Solar Security Camera Outdoor Wireless - 2K Battery Operated CCTV Camera Systems, Home/House Security, PIR Detection, IP65, Colour Night Vision, TF card Storage, (2-Pack)

What’s Included.• The camera itself• A wall-mount with 360 degree swivel bracket, a drilling template, and screws with wall fixings• USB3 charging cable• Certificate of Conformity• 24H Surveillance warning sticker• Quick Start GuideSetting upInstallation was the quickest I have experienced. I was pleased to see that this camera uses the WANSVIEW app, which I already had on my phone. Pressing the POWER button for 5 seconds followed by pressing the RESET button for 5 seconds resulted in the indicator light flashing alternately red and blue. These buttons are located beneath the flap on the top of the camera.After tapping the Add Device button on the app and pointing the camera at the QR code on the app, the camera announced by voice that it had successfully been added to my network.Immediately the image from the camera appeared in the app, together with my other Wansview cameras. Selecting the settings symbol resulted in a window informing me of the Wifi strength and battery charge.Next to the POWER and RESET buttons there is a USB3 slot marked DC 5V, and another marked TF. The DC 5V is for charging the internal battery should there not be sufficient sunlight to charge it during use. I did not need to charge the battery as the app informed me that it was already at near full charge.The TF (TransFlash) slot is for a memory storage card for local storage of images and video. Although it says TF, I managed to insert a 32GB micro SD card. The app detected my 32GB card then included a section for Memory Card Storage. There are a few options associated with this, like Motion alert ENABLE, when to record (scheduled or 24/7), space remaining, and action to take when storage is full (overwrite earliest recordings or stop recording). It also had options for custom recognition and notifications including person recognition.There is no need to subscribe to a cloud based subscription if using the memory card.InstallationThis involved mounting the camera at a suitable location. This would be a wall or any flat vertical surface where the view required is available. Note, however, that the location must have a good 2.4GHz WiFi signal.The mounting bracket is easy to fit. The template can be stuck to the surface and then the holes drilled where indicated. I found that it if the swivel mount is unscrewed form the mounting base, it was possible to hold the bracket against the mounting surface and then to drill using the holes in the base. The swivel mount has a threaded stud which screws into a socket on the back end of the camera, and the swivel bracket is held to the base by plastic collar. This should be loosely attached so that the body of the camera may be rotated and angled as required before tightening the collar.My attachment was to a wooden beam, so the supplied fixings were not required.In UseThe image on the app was bright and sharp and declares itself on the image to be 2K, which is similar to High Definition (HD) or 1920 x 1080 pixels. As I watched myself on the app walking towards the camera, there was very little delay and movement was smooth. The app allows the image to display individually with options in the main screen, individually at full screen or with other Wansview cloud cameras (if any) in a grid.The settings menu provides access to various other functions built in to the camera, but at the top of the main screen is a useful indication of WiFi signal strength and the battery charge percentage. If sunlight is detected, then the battery symbol alternates between blue and green to indicate that it is charging.On testing the alert function it appeared that an alert was not triggered unless the movement was close to the camera. Checking the Motion detection settings revealed that by default these have been set to Power-save mode (see screenshot above). Clearly, with a battery powered camera it is important that the battery drain does not exceed the solar charging capability. In a British winter, I’m not sure how this will work out even in Power-save Mode. The settings available are:POWER-SAVE STANDARD PERFORMANCESENSITIVITY LOW NORMAL HIGHDETECTION DISTANCE NEAR NORMAL FARRETRIGGER INTERVAL 60 SECS 30 SEC 0 SECSThe camera did trigger an alert and it did record me but not until I had reached the camera and started to walk away, but in the light of the above explanation I think this is acceptable. I changed them to Standard Mode, and this time an alert was triggered when I was about 5 metres away from the camera, so I think Performance mode would increase this distance further.The battery indicated that it was 60% full after running for 5 days in Power-Save mode in poor sunlight weather. After changing the settings to Standard, the battery indicated 48% after about 4 hours. However I was creating a lot of alerts in that time by walking back and forth to check it. With it still in Standard mode but with nothing to cause an alert, it is still showing 48% 2 hours later.Reviewing the alerts is achieved by selecting the Replay button on the main screen of the app. This will open a timeline showing where the alerts have occurred, and allow the video at that time to be viewed.Night vision is very good, with the built in infra-red lighting automatically switching on when darkness descends (see screenshot above).SummaryA very impressive camera – easy to set up and good quality images were obtained day and night. The alert function can be adjusted between power saving and sensitivity. The only minor issue I had was the camera slipped slightly during a high winds. Make sure the swivel bracket is fully tightened.Update after 2 months’ use (Mid December to Mid February 2025)The camera has performed faultlessly, providing clear images, day and night. Particularly impressive is the fact that its solar panel has now charged the battery to 100%, as indicated on the display. No charging cable has been attached during use. This is despite the fact that I have set it to Performance Mode, with the motion sensitivity at HIGH, detection distance to FAR and retrigger interval to 0 seconds.

I think this is a really impressive security camera - especially at this price point! It's straightforward to set up and has a really useful array of settings/sensitivity levels. The quality of the colour video it records is more than decent enough - and I love that it is solar-powered and I didn't have to get someone to wire it in ... I had an initial problem with not receiving the verification code email - and so got in touch withh Aoqee customer support. I had a really prompt and helpful response (they offered to activate my camera remotely if I experienced further problems - this wasn't a generic message!). Fortunately I received the verification code the next time I tried and everything has gone smoothly since. Since I am disabled, I cannot get down the stairs quickly enough to answer the door. But now I am able to both see and speak to any visitors (I don't need to get a video doorbell even - and this gives me more coverage of the surrounding area). So, no more panicking when the doorbell goes and I'm upstairs - and I feel a lot safer now too ... Well done to Aoqee - I will be recommending this camera to friends and family etc. ...!!

Fantastic Camera at a great price.For the price , I think you would struggle to get a better camera.Delivery was under 8 hours , so that's a big plus.From unboxing it , to seeing the video footage was less than 10 minutes , so very easy to useThe camera is super easy to set up using the Wansview app , as a user of multiple products by this vendor , it was very easy to add this camera to the existing app.I don't know about the WiFi chip , but this has got a further range than any of the other cameras I have. I have managed to mount it approx 100 feet away from the nearest Access Point , and it still connects to the WiFi fine.Being Solar Powered means no need to cables running everywhere , especially outdoors.The battery does charge in sunlight and it keeps its chargeThe unit itself is well made , and doesn't have the 'cheap and nasty' feel you get on some cameras. It comes with all the mounting hardware you could need , including a template to drill the holes if needed.Takes a 32gb MMC card , so no need to pay for a subscription.Picture quality is excellent , and seems to be 2 , night vision is also pretty decent.I was surprised by the strength of the LED lights , almost blinded myself whilst seeing if they worked.The siren is a nice touch as well.2 way intercom is also good.Links easily enough to the Alexa App , and push notifications work with only a minimal delay between camera activation and notifications being received. (5 seconds).Also the ability to view the camera feed directly on an Echo Show is a nice touch as well.Pros:Ease of usePrice pointFunctionalityConnectivityCons -Not really cons , just 'would be nice if'Volume adjustment on siren would be a nice touchThe power and reset button are a bit close and fiddly to use , and the labelling of the buttons could be a bit better