Pool Mate 4-Pounds Premium Pool Stabilizer and Conditioner, Concentrated Cyanuric Acid for Pools, Helps Chlorine Last Longer

Worked as described, Easy use directions. Why pay high prices at the store when this product works.

use for the pool. works good

The Pool Mate 1-2604B Pool Stabilizer is an absolute game-changer for maintaining a healthy and efficient chlorine balance in my pool. Living in Texas, where the sun can be relentless, keeping chlorine from burning off too quickly is a challenge—but this stabilizer does the job perfectly!🌟 Why This Product Works So Well:✅ Protects Chlorine from UV Rays – Drastically reduces chlorine loss, so I don’t have to add chemicals as often.✅ Saves Money on Chlorine – Since the chlorine lasts longer, I’m using way less over time, which cuts down on costs.✅ Dissolves Well – Unlike some stabilizers that take forever to mix, this one dissolves efficiently when added properly.✅ Keeps Water Crystal Clear – Helps maintain consistent chlorine levels, reducing algae and cloudy water issues.✅ Works for Saltwater & Chlorine Pools – I use a saltwater chlorinator (Intex QS1200), and this keeps my pool perfectly balanced.If you're tired of chlorine vanishing in the sun and constantly having to adjust levels, this is the stabilizer you need! Just be patient—it can take a few days to fully integrate, but once it does, you’ll notice a huge difference in chlorine efficiency. Highly recommend for any pool owner! 🌊🔥

I have used this for several years and it definitely works as advertised, it increases my conditioner level by the amounts indicated on the lablel.My only negative is that these small pellets don't disolve very easily.Pretty much the only way I could use them is to put the pellets in the skimmer basket and run the pump for the recommended 24 hours.The instructions say to only do it through the skimmer if the filter is clean.Also, since I have a salt water pool with a salt cell, I was concerned about cell damage if I added it directly to the skimmer, so I shut off the salt cell for 24 hours.Basically, it works, but it's not as convenient to use as a liquid.Note:The instructions say you can disolved it in pool water and also suggests warm water. When dissolved, you can add the solution directly into the pool.I have tried cold, warm, and hot water and see no difference. I have used a paddle paint mixer attached to a drill, and sill get very little to dissolve.Bottom line, plan on adding it to the skimmer a few pounds at a time with a reasonably clean filter and run your pump for 24 hours.

Local pool store is way over priced on stablizer so this is a good price and a heavy box.

First off, I've read some 1 star reviews by people that clearly have no idea what this product is, how it works, or how to use it. This is 100% Cyanuric Acid (CYA). While it says Stabilizer and Conditioner, this is one ingredient.CYA is a chemical that acts as a chlorine stabilizer. It forms a protective shield around the chlorine molecules in your pool, preventing them from breaking down when exposed to ultraviolet (UV) rays from the sun. The recommended amount of CYA in your pool can vary depending on whether you have a saltwater pool with a Salt Water Chlorine Generator (SWG) or a traditional chlorine pool. In a traditional chlorine pool without an SWG, the recommended range for CYA is 40-50, whereas a salt water pool would be higher at a recommended 70-80.Adding CYA to your pool is important for maintaining an effective chlorine level. Without CYA, the chlorine in your pool can quickly dissipate due to sunlight exposure, requiring you to add more chlorine frequently. By using CYA, you can extend the lifespan of your chlorine, saving you both time and money.How to add it:Do NOT just dump it into the pool. CYA takes time to dissolve fully in the water. By just dumping it into the water, it may not dissolve properly and could settle on the pool floor, or worse, clog the filter.Instead you can either use an old sock, or (see photo) my favorite method is some sack cloth. Measure how how much you need, following the instructions carefully, then letting it soak for 12 hours. If you see my photo, I do it this way so I can place the skimmer lid back, and keep the cloth from falling into the skimmer (don't let this happen). Also, make sure the pump stays running for 24 hours during and after adding CYA.You can speed the process up by massaging the sack, just don't do this too vigorously otherwise you'll end up with CYA granules falling out.Notes:CYA does not break down or dissipate. It remains in the water for an extended period of time, providing its stabilizing effects on chlorine. Unless you have had your pool water replaced, or you have a new pool there is no reason to keep adding CYA.CYA levels can gradually build up in the pool over time, especially if excessive amounts are added or if the water is not diluted or partially drained and refilled periodically. This buildup can lead to high CYA levels, also known as "chlorine lock," which can negatively impact the effectiveness of chlorine. Monitoring and testing CYA levels regularly is crucial to maintaining the appropriate range for optimal pool chemistry and chlorine stability.

I like to get this from this seller because it has happened to be cheaper the times I've needed to purchase it, and it comes the next day. Always reliable.Works exactly as directed, and quality product.Our pool is sparkling and clean and living in Florida, we have to keep our pool kept all year round.Highly recommend this stabilizer and this seller.

Works but have to use more than the directions indicate.