Foot Pedal Pads Set for Tesla Model 3 Model Y, Non-Slip Performance Aluminum Car Accessories Brake & Accelerator Pedal Covers for Model 3/Y (Red)

These pedal covers make a big difference in the appearance of the car, going from econo-car rubber pedals to sport-type slotted aluminum ones. I got the silver aluminum ones, but they're also available in several colors. They're inexpensive and easy to install (if you do it right).On that note, DO NOT watch the customer videos on the listing page. They didn't read the instructions and aren't installing them right. The lady who says they don't fit the 2025 Y is also wrong.1. THE ACCELERATOR PEDAL COVER SLIPS ON FROM THE BOTTOM OF THE PEDAL UPWARDS, AND IT'S A 2-MINUTE PROCESS.2. THE BRAKE PEDAL COVER IS A LITTLE MORE FUSSY, BECAUSE YOU WANT A REALLY TIGHT-FITTING COVER FOR SAFETY. IT TAKES A LITTLE MORE PULLING AND STRETCHING. A HAIR DRYER OR HEAT GUN WILL HELP WARM UP THE COVER TO MAKE IT EASIER TO MANIPULATE. BUT YOU FIRST HAVE TO REMOVE THE EXISTING COVER BY PULLING ON THE EDGES AND WORKING IT OFF.3. THEN HOOK THE RUBBER LIP ON THE BACK OF THE PEDAL COVER ON THE TOP OF THE BARE PEDAL AND START PULLING THE COVER DOWN AND OVER THE SIDE EDGES OF THE PEDAL WITH YOUR FINGERS.4. THEN START WORKING THE BOTTOM LIP OF THE COVER OVER THE PEDAL. THIS IS A LITTLE HARDER, BUT BE SURE YOU HAVE ALL THE LOWER RUBBER LIP HOOKED OVER THE METAL PEDAL SO IT DOESN'T COME LOOSE. PULL ON THE LITTLE TABS ON THE COVER AS NEEDED TO HELP GET IT IN PLACE. A SMALL MIRROR AND FLASHLIGHT ARE HELPFUL FOR THIS STEP, TO LET YOU CHECK THE BACK OF THE PEDAL.Once installed correctly, these covers are securely in place and they add a lot of pizzaz to your otherwise dark and dull floorboard. Functionally, they provide a good non-slip surface on the pedals, and they're easy to clean. And they're inexpensive. I like them and give them all 5 stars.

These pedals look amazing. I have a red 2026 Tesla MY and they fit perfectly. Installation was easy though it was a hot day and the rubber was softer. Gas pedal cover fits the existing plastic pedal. The brake pedal requires removal of the existing rubber cover. The red one then slips on with a bit of finger power working the rubber backing. Overall took less than 5 minutes to install both . Looks amazing !

I really like the look and feel of the pedals. The instructions were clear and easy to follow, and getting the new pads installed only took 5 mins. What took me the longest was contorting my body to be able to comfortably install them.But the pedals look great in my M3 LR RWD, have a nice & grippy feel when I use them, the price was reasonable, and overall I’m very satisfied with my purchase.

So good so far and that awesome red color really stands out!These are installed in my 2020 Land Rover Range Rover HSE P525. The brake pedal was a little challenging the accelerator pedal not so much!Great choice and quality highly recommended!!!

It did not fit my car. The website says it fits the Tesla Model Y but it didn't work.

I got these to replace the silver ones I had on my Tesla. PITA to get them off if you need to remove, but that is what you want when they are on. Snug fit, looks great.

Look nice but are hard to get on. I warmed them up to make it easier to fit.

I like this over the Spigen more racing-style. There are reviews out there talking about better materials, and real metal. That could be true, but these $15 dont look bad at all, even though it could be a plastic resembling aluminum. The installation was 5 mins in my model 3 Highland. Either some people are trying to fit these without removing the previous pedal cover in the brake or the material is more flexible in newer shippings. Just takes moderate force to pull the back apart and get it to wrap pedals. The rubber lines seem to be OK and hold the stepping. We ll see. Some had some little extra rubber that I was able to cut with the tip of a knife.