Front Lip ,HengJia Auto Parts 2.5m/8.2ft Car carbon fiber front lip,Front Bumper Lip ,Carbon Lip ,Side Skirt, front lip spoiler 100% waterproof protection(Carbon black)

So look in the pics and see that this is the correct way of installing this. First off I cut relief spaces around 4 inches apart. I used like 50+ nuts and bolts w/ red loctite. Once lined up (pretty much just eye balled it) on the bumper drilled one hole at a time and dropped a screw in without a nut. Once I made it all the way around i pulled off the rubber and made sure everything was clean and smooth. Once cleaned all was left was to pull the backing off the tape and put on the bumper making sure the bolts lined up with the holes going 3 sections at a time. Then this is the most rewarding part....Must have a heat gun ! Break out the ol heat gun and start warming up the rubber making sure ya don't cook it. Just get it to where you see it start to move a lil with the heat on it swiping back and forth in foot sections. All those imperfections are now gone (wavy notes on the rubber due to curves and what not). When the rubber cools down it will get more stiffer again so don't worry if it feels soft. All your looking for is crisp even lines. You'll understand when you get it out the box and pieces look like " how the hell is that gonna even out". The 3m tape pretty much is garbage and I knew that from jump street so I could have gone with rivets or bolts. I went with the latter just in case i need to replace it one day. Looks at the pics I have a 2014 Hyundai Sonata and it pops now with this on there !!!

OK 1st off the problem with this thing is that I really genuinely wanted to love it one it does not say samurai on it it's just carbon fiber color. To the eat it provides for screws to attach it. The problem with that is that there is adhesive also but it only lasts for about 5 days. So the moment you put it on it will look great but within a week it will be sagging down everywhere. I added about 10 more screws and it still sag in between each screw. I put it on a Porsche Panamera and and looked cool at 1st but I had to rip it off within 2 weeks next time I will buy something that is made out of hard material double not sag due to basic I. Understand that it is summer time but this is a very temporary purchase and should only be used if you expect it to look good for a couple of days. Don't waste your money find something that is made of hard plastic not rubber that has poor adhesive

Installed on a Subaru Crosstrek. Be advised that it has an obnoxious chemical smell upon opening. Just lay it flat in an unoccupied room for a few days. The smell mostly goes away. The installation instructions were in Thai. Lol But there are pictures tho.Had to clean the underside well with wipes/soap/water/alcohol. The cleaning may take a few rounds, but very important. It won’t stick to a dirty surface so don’t get mad if it falls off later on bc you’re too lazy to spend the extra 5-10 minutes to really clean the underside. (Just saying.)It comes with two adhesive promoters but it should have come with 3. They dry out pretty quick, but are essential for the adhesion process.It does take some time to measure and cut out the “triangles” for the bends. I just used a pen to mark on the red tape to guesstimate where the bends are and marked the triangles from there. Also, you’ll have to force the lip to bend. The lip is rubber, it’s not all that elastic.Would also recommend utility scissors to cut the triangles too. The rubber is thick enough that I’m not sure normal scissors will get the job done. I had to use two hands to clomp down on the scissor handles.It’s been 3 days since the lip application. Hasn’t fallen off so that’s good. Also haven’t used the screws yet but will probably put them on. Haven’t braved sending it thru a car wash just yet so may have to send an update for that later on.All in all I like it so far. Considering buying two more for the side skirts IF the front lip lasts thru a car wash. Lol I do like that it’s rubber bc cracking a real lip kit would make me cry.*Update (4/3/18): Front lip still on after 4 automatic car washes and a couple of thunderstorms later. Still haven’t gotten around to putting the screws on either. 👍**Update (2/4/19): Front lip still on. Eventually had to add 2 screws to one of the bends bc it was starting to fall off at the ‘corner.’ (This was the same place I had to cut “triangles” to make it bend.) The screws were recently installed in Jan. 2019 so the lip held up well with all things considered.Sadly the front lip had an unfortunate run in today with old debris from a blown tire. The car in front of me kicked it up so fast that I didn’t have time to swerve or brake safely at highway speeds. Poor car took it like a champ. =/Oddly enough, the lip is still on. However, the center portion of the lip split horizontally right where the lip and adhesive part meets in the middle. Will probably have to replace it eventually as rubber will degrade making the gap even longer. However, I will be purchasing another three once it’s time. I’ll redo the front lip but also add side skirts.***Update (03/05/20): The original lip is still on! The adhesive is wearing off on one end near the wheel well, but not bad for 2 year application. Got lazy and used Velcro to keep it on for now. The split in the middle has widened, but still safe to drive with. Ran this thru the car wash well over 30+ times. Some of the carbon fiber graphics has worn/scratched off, but still decent shape with all things considered.

Definitely looks decent, but the 3m tape is incredibly lackluster. The first one I installed fell off within a couple days. I contacted them and they sent a 2nd one out and this time they included tapit screws, which I suggest buying at just another 20 before installing this lip. Every 3-4 inches install a screw, and make sure to do it in key places like the corner of a turn, it if the lip has to go up or down to follow your bumper.It's fairly stiff material, but not so stiff that it'll not bend do to high speeds on the highway.Overall decent product, but definitely could use some improvements/include 20-30 tapit screws off the bat.