VFD 4KW 5HP 220V 1 or 3 Phase Input 3 Phase 0-400HZ Output 26A Variable Frequency Drive Controller Vector Control Inverter Converter for CNC Motor Speed Control and Spindle

Excellent, it works perfectly. I used it for my cylinder head grinding machine and it worked without any problems.

I use this to add a 2nd and 3rd phase to be able to run my 3 phase air compressor. I reached out to their support before I bought it and they were very helpful. They wanted a picture of the data plate from the motor and had their engineers review to recommend which size I should get. I mentioned to them that it was for an air compressor and they even provided instructions to set it up to work with my pressure switch! I would highly recommend this VFD if you only have single phase and want to run a 3 phase motor. (Ignore my wiring. I tried another VFD first and ran 10/3 with a 30A breaker. When I switched to this one I ran 8/3 (you can use 8/2 though) with a 40A breaker. I just haven't tidied it up yet. )

I bought this VFD to replace the Westinghouse/TECO N3 VFD which failed on my 2HP Bridgeport milling machine. I think the unit is actually the ISACON A2 Series, I'm not sure if HKS rebrands it or if HKS is part of ISACON? This unit is considerably smaller than the TECO N3 and only has 2 mounting holes. There is no strain relief for the AC line input wires nor the motor output wires. I used the strain relief bracket off of the TECO, but this still leaves the wires exposed. I took off one star for no strain relief. I'd also prefer it if all the wires were completely enclosed. With the wires exposed, I'm not sure if this unit meets US UL wiring code or not? The terminals for the AC line input and motor output are also quite small, I used forked terminals for a US #6 stud (or you could use whatever the metric equivalent is), this means you'll probably have to use #12 GA wire or less. I followed the instructions given in the "Set The Initial Test Parameters" found on the Amazon page for this unit, I just changed the PN02, PN10, and PN12 parameters to 60Hz instead of 50Hz (I'm in the USA). The instruction manual is very brief but adequate for what I needed, but could be better explaining some of the more advanced features. The turn on and turn off acceleration default to 10S and are much slower than the TECO unit, but these can be easily changed with PN08 and PN09. I used an external pot on the TECO N3 to change the frequency and thus the motor speed, but this can be done on this unit with the UP/DOWN buttons on the front panel, which is nice feature. You can also set it up to use an external pot if you want to. Initially I like the way the unit works, the front panel seems fairly intuitive, and everything worked as I expected. The price is certainly appealing, much cheaper compared to something like the TECO. It will be interesting to see how it holds up in the long term, but I would certainly recommend it at this point especially for a home machinist such as myself.

Got this for a gift and it doesn’t run a 7.5hp motor. Putting out over 500v on the 3rd leg and displays error message. Tried contacting support and no way to get ahold of the company. Do not recommend!

It works fine but the instructions for the settings are unclear

They arrived and worked. I had these old molloms, these were less complicated and easier to use, with clearer labeling for the one phase power connectors. Both worked for my purpose. I returned them, but only because the owner of the building I was in offered to pay for them to replace one of the broken ones.

I bought two of these, one for a .5/1/0 hp motor, one for a 1/4 hp motor. After pondering the translations in the manual, I was able to get both units set up and running. In the case of the .5/1 hp motor, the drive complained of overcurrent during acceleration. After fussing with the torque boost and increasing the acceleration time, I was able to get the unit to operate without error using the .5 hp winding at 20 seconds acceleration, but not the 1hp winding. My conclusion is that while the drive may be capable of operating at 1hp (750W, 4.2 amp/phase) it is incapable of supplying the additional current for startup... I kept the unit operating the 1/4hp motor and returned the second unit in favor of a WEG CFW300 1hp unit, which, although the parameter setup is a bit arcane, worked flawlessly right first time with 2 seconds of acceleration to 60 hz.

It worked for a while but would not restart where you left off when you took power off. Now all of a sudden it just flashes numbers and does nothing. The manufacturer is always out to lunch. No support from them or Amazon. Stay away if you need a product that works in a production environment.