Sportway S60 Dash Cam Mirror Mount with 10pcs Joints Kit for Rove APEMAN CHORTAU Roav Nexar iiwey YI Z-Edge Old Shark Rexing KDLINKS Falcon Zero Transcend Crosstour VANTRUE... Most Car Dash Camera

Not only is this working better than the suction cup that the camera came with , it also lets me get the camera cord out of the way by being lower to the dash . It puts the dashcam right at eye level and instead of being off center of the truck windshield it is now dead center and I get a true WDR recording .Installation was a breeze . I do not have my rearview mirror clicked into place because I like to remove it vs fighting it when I use sun shades so that's another plus vs the original dashcam holder . I don't have to fight it when using my sun shade anymore .It was a bit difficult to get the bolts super snug and i have a feeling I'll be occasionally snugging them up again because wing nuts vibrate loose pretty easily sometimes but everything else is rock solid .The low profile is being mostly behind the actual mirror is a major win for me . That and how easy it is to remove the camera from its clip now make it worth much more than what I paid for it . Great design .

I used this with a rear view mirror power adapter to get a clean look. This allowed me to remove the suction cup from the windshield and the wire from the ashtray.The adapters were very comprehensive, but the one that most closely matched mine (in pictures), was a few milometers too wide and a few milometers too long where it connected to the dash cam. Five minutes with a soldering iron and a razor made it a good fit and I carried on.The quality is high enough. It holds the camera still while driving. It could tuck farther up and behind the rear view if the USB connector didn't block it from bending more, but that's the dashcam's fault.

Good product. Has many different ways to attach the camera to the car. It didn’t have the size that I needed but I rigged it to fit

So I purchased this mount some time ago and I can say I am very satisfied with it. Not only because it keeps the camera steady but also for all the different mounts it has.I was looking for a mount that would not melt during the intense heat of the summer and did not fall off and this mount did the trick. It installs right behind the rear view mirror into the base and once you tighten it it does not move. It has two long screws and nuts that allow you to tighten the base to the rear view mirror. It is a bit uncomfortable to mount it as you need to completely move the mirror until you are comfortable to tighten the screws but it does not take much time nor effort.Choosing the correct attachment for your camera is very easy.For the time I’ve had it, it has work great and I am very satisfied with my purchase and I would recommend buying it

This camera mount is easy to use, and with a little bit of patience, easy to install. It is very sturdy with a lot of adapters. Unfortunately, the adapters that came with the mount, did not fit my camera. Being rather creative, I fixed that issue by taking the ball connector out of the suction cup mount that came with my camera, and fit it to this mount. Worked like a charm!I love the fact that this is sturdy on my rear view mirror, and is only about 1/4" in width. I have a rear view mirror that has all of the "bells and whistles" on it like, automatic headlights, dimming, etc. I also do not have a lot of room near my rear view mirror due to the electronics (rain sensing windshield) attached to the windshield. With this mount, I don't have to remove the camera to put up my sun screen (a must for a anyone who lives in Florida) and, should something happen to my current dash camera, and I get a new one, I can still use this mount without having to remove it from my mirror. I would just have to loosen the screw where the mount ball and the camera ball connect, pop out the camera ball mount, and put in the new one. This is a very simple design, but a much needed accessory for anyone with a dash camera!

Works perfectly. I have 5 cars in the family and I have one on each car. I got into none fault accident couple of times and saved me from defending my case. I showed it to insurance -- problem soved.

This is a review for Sportway S60 Dash Cam Mirror Mount with 10pcs Joints Kit for Rove APEMAN CHORTAU Roav Nexar iiwey YI Z-Edge Old Shark Rexing KDLINKS Falcon Zero Transcend Crosstour VANTRUE... Most Car Dash CamerasFirst off, my camera was listed as compatible, and even had a picture of it mounted. I have a rove camera, and I had to use a file to modify the bar that slides into the camera in order to make it fit. As a customer, I shouldn't have to modify a new product to work in something that is allegedly compatible. I knocked two stars off for that alone.Other than the above mentioned issue, it mounted to my mirror easy enough, and so I didn't knock off any other stars. It seems sturdy enough, but time will tell.If you have tools, and don't mind modifying the item, I will recommend it, but if you don't or aren't comfortable doing so, then you may want to look elsewhere.

My suction cup mount eventually melted from the hot sun. I found this mirror mount on Amazon and I’m very happy with it. There were several different adapters, so I was able to find one that works for me. I was able to securely mount it to my rear view mirror. It was fairly easy to install and it seems to be pretty stable. It hangs just low enough to clear the box that contains my sensors on the windshield, but it isn’t too low that it interferes with my line of vision. I like the design and think it was a good value for my money.