UTEBIT Dual Flash Bracket 30cm/11.8 inches Extension Flash Bracket Aluminum Alloy Straight Flash Tripod Mount Bracket DSLR Camera Brackets Holder for Camera LED Light Flash Light Microphone

Excellent piece of kit to have which is well made and dose the job well. 5 Stars.

The extra length was just what I needed.

Works as you'd expect for a simple device but the screws are a little too long for a couple of my attachments.

I brought this item and it is extremely quality. It’s built with a strong metal design.It can withstand other items on line.It holds very well with camera, lights, or other items too.I like the fact it holds every device securely without topping or overweight.It slides smoothly along the rail, & it tightly tightens all your 1/4 inch devices without any problems.This is the very best one I’ve brought & would definitely recommend this brand.If you want quality like I do then this is one to buy. This utebit is highly professional quality.Others I’ve seen don’t have strong durability. I rate this this a 5 stars.

Bought this item in order to mount two action cams side by side. Item arrived as described and within the specified time. It is a piece of machined and anodised black metal, ostensibly aluminium. The bracket is about 4mm thick, and resists casual bending: some effort might be required to bend it (but I'm not about to try too hard!). At the centre are a 1/4 inch and 3/8 inch threaded hole (with the actual mid-point of the bracket length falling directly between the holes, i.e. both the mounting holes are offset from centre by about 5mm). To either side is a long machined slot, about 6mm wide and approx 125mm long with each slot occupied by two 25mm wide thumbscrew 1/4 20 threaded camera mounting points that can be moved back and forth at will along the length of the slot; the underside of the thumbscrews also have a threaded 1/4 20 inch hole. The bracket is essentially as is described in the Amazon page.However...Unfortunately, the issue I had was with the length of the screws that are supposed to secure the equipment. Every camera I tried (2 action cams, 2 point and shoot cameras and 3 digital SLRs) failed to secure tightly enough. Despite turning the thumbscrews as tight as possible, there was still considerable play in the mount, and it was impossible to point the cameras without them moving. Having brought a screw-in handle to carry the mount and cameras I was left with a mount that was effectively unusable. From an examination of the bracket it seemed that the camera mounting screws were a fraction too long (only by about 1-2mm) and so weren't able to pull the foot of the camera body tightly against the bracket to secure it in place. So I had three choices: return the mount, reduce the height of the screws or find another solution.I needed the mount, so a return wasn't much of an option. I didn't fancy taking a file, angle grinder or Dremel to the screws to reduce their height, so I had to consider something else. In the end what I did was bought some foam rubber, self adhesive furniture pads (specifically, Grevosea 93 Pieces Furniture Pads Non Slip Furniture Pads Floor Protectors Self Adhesive Chair Pads Round Furniture Pads for Protecting Hardwood Floors 8 Sheets 1 Inches Black). I punched a 4mm hole in the middle of four pads and then stuck them over the upper surface of the camera mounting points, so that the threaded bolts popped up through the central holes in the pads. With the extra thickness of padding, securing cameras was a doddle, and all the cameras that previously moved loosely on the bracket could now be secured.So, as a bracket, is it worth it? Yes, it's worth the money and offers flexibility in use. However, you may (like me) be forced to splash out on the added expense of some self-adhesive pads in order to make it into the functional item it should have been in the first place. But on the bright side, I have lots of pads left over: it's just that I can't think of any nefarious uses for them at the mo... :-)

This bracket is pretty simple, with high build quality (seriously, I actually tried to bend it--it wouldn't) and great fit and finish. It'll mount four small cameras, flashes, or anything with a tripod mount with no issues whatsoever. This is wonderful for my application of using a depth sensor alongside a mirrorless camera.I'd recommend it!

Bought these so I could add things beside my Camera, things like lights, microphone even a backup battery holder. These are solid and sturdy, I am predicting I will have these for a long time.The 2, 1/4 fittings are male one side and female the other with soft rubber mounting washers provided, you can get them out if you need to turn them round as well.

I used this to mount a an LED illuminated slide / negative carrier and an Canon EOS-70D. The Camera needs about 20mm extension tube and 18mm-55mm lens (or about 45mm to 50mm). I used a spacer to lift the camera held on by one screw and then 2nd screw is on rail.Mounted on a wooden base board for table use with two wood screws in the slots.One end of each slot is already threaded so you can remove the mounting screws.I'm sure it's also great for a flashgun or other accessories.

La verdad que funciona bien y se ve resistente

Conforme et très bon produit

Hält was es verspricht! Stabil und gut zu Händeln. Hatte bisher nur leichte Cameras drauf, aber die sitzen fest und wackeln nicht! Passt auf die Manfrotto Schnellkupplung!

Matériel bien fini super

Ottimo prodotto.