Manual Wire Stripping Machine Speed 50FT/MIN Wire Stripper Machine Wire Gauge Range 0.06-1inch Portable Copper Wire Peeler Machine Two Blades Included for Scrap Copper Wire Cable Stripping

Of approximately 1500 lbs of wire, 98% was done on the machine. Overall and including labor to prep the wires, it took (1 man) about 4 days. My scrapper is the only one in town (monopoly) and the next one is over a 100 miles away and is the same company but, it is what it is!Back to the machine! I tried to strip 1" diameter copper wire, 30+ feet coil's (2 of them) and messed up my blade because it was turning in the machine and made it serrated, but it still cut, the solution was to cut the coil's into more manageable pieces of 5' ft length. Although it is a simple machine, it will take a lot of trial and errors during the learning process but, well worth it. The green "ON" button is designed so that if you want to control the power manually or depress it all the way in for constant power "Great design". I don't know if I messed up the blade but even after sharpening the blade, it wouldn't strip #14 gauge solid wire. I recommend if you get a brand new machine, to do a practice run of all the sizes you have, to see what is the minimal size it will do......My machine paid for itself already, so I'm pleased with it.... Like everyone who has at one time or another, I have manually stripped copper wire, and while looking at my aching hand and only halfway through, telling myself "I will never do this s@#t again", but as we are all "creature's of habit" I just can't walk by a piece of scrap wire or copper pipe....actually I might walk by but I'll probably turn around and go back to get it, lol....I don't do this for a living, I was given 99% of the last load I had, but I sat on it for over a year and dreaded doing it manually until I saw this machine on YouTube, and now, "bring it on" LMAO..... I think I will change my user name to, as we say in Hawaii "Just Scrap" lol

I had just over 5000 feet of braided 12 gauge wire that I needed to strip. I was worried about this product due to the cost but didn't want to spend 300+ on another one. The machine arrived as promised. I found that there are a couple things that you can do to make it work perfect. First, organize your wires by size. Second spend a few minutes fine tuning the space between the cutting wheel and the drive wheel. I did both and stripped the outer case from the big cord then the smaller case. I was able to strip all of my wire in about 4 hours. I attached my drill to it instead of the handle and set it at a slow speed. Make sure that you adjust the wire alignment bracket on the front and have it pull the wire up. Great product and paid for itself on the first use. HIGHLY RECOMMENDED!

I wish it had smaller guide holes to guide smaller wires. But other than that it worked perfectly even for all the smaller thn wire with plastic insulation. Stripped with ease after I got the machine adjusted correctly. Love the drill attachment feature, sure beats cranking it by hand. Just a word of advice, only use the low speed or number one of your cordless drive. It does better with the ratio of the stripping machine. Almost burned up my drill trying to use it in high speed (2).

Works amazing. Writing this review after using a hundred times. All size wires. I stripped the side bolt using drill from the drill flipping in and out of nut attachment and there’s no replacement but could have been avoided. There is just no mount to hold your drill straight when using a drill. So just be careful to keep a straight angle or over time it will strip

This device does not strip wire accordingly. The design does not allow the blade to slide along the top to cut into insulation. Instead the wire comes off the blade. Causing the blade to rub along the wire without cutting into it.Very disappointed in this purchase.

Works well on certain sizes of wire. Works poorly on wire less than 1/8 inch.There is a learning curve and you have to set it up right for each size wire.

So hard to watch my son with a utility knife stripping wires. All i could think of was an ER trip. I saw this on Amazon and instantly ordered so we stopped. Received 3 days later. My son and his work buddy stripped all the wire so quickly. They were super impressed with this machine and how easy it was to use. Now they are looking forward to stripping more wire. This machine was SO worth the money-Mother of the year

The media could not be loaded. Very good quality and easy to use.well made and nice finishingwork good and efficient