⚙️ Upgrade your wash game with rock-solid reliability!
The Popbee Washer Rotor Hub Assembly (PBT-GF30, model 4413EA1002B) is a premium replacement part designed for LG and Kenmore washers. Featuring a durable metal core encased in reinforced plastic, it offers enhanced stability and longevity. Compact and precision-engineered, it fits multiple washer models, ensuring seamless compatibility and easy installation. Tested for performance, this rotor hub assembly is your go-to solution to restore washer efficiency and avoid costly downtime.
| Brand | Popbee |
| Color | Black White |
| Material | Metal and Plastic |
| Style | Washer Rotor Hub Assembly |
| Product Dimensions | 4.13"L x 4.13"W x 0.9"H |
| Power Source | Ac/dc |
| Item Weight | 0.11 Kilograms |
| Manufacturer | lyavo |
| UPC | 769044055390 |
| Brand Name | Popbee |
| Model Info | 4413EA1002B |
| Item Weight | 3.84 ounces |
| Item model number | 4413EA1002B |
| Part Number | 4413EA1002B |
| Material Type | Metal and Plastic |
| Batteries Included? | No |
| Batteries Required? | No |
M**O
Great part
Worked great, direct replacement.
A**.
Very low cost fix for error code
Had a spin error code. Replaced this on my washer because teeth wear bad and OEM part was plastic! This part is much better as the teeth part is metal.
A**R
Good replacement part
Make sure it is properly centered when installing, the original was all plastic in the center, hoping the metal shaft mating will hold up better
M**T
Perfect fit.
Fits perfectly. A little thinner than original. I did not have to use spacers like other people have suggested. Took about 10 minutes to get my washer working like new.
S**T
Beware of fit
I have an LG WM2501 washing machine and Amazon says this part fits the rotor. I installed it not thinking that it wouldn’t fit correctly. Went in fine, put the washer back together and did a test run. I hear grinding. When I took it apart again I measured the old par to the new part. Off in height by almost an entire centimeter causing the rotor to tear up the stator causing more than $400 in damage. Don’t buy!
R**
It fits
Glad these are available, otherwise I would have had to buy the whole assembly that costs $160!!!
N**C
Both of mine were warped and would not sit flush in the rotor casing - but can be fixed.
Just received mine in. Bought two because I knew at least one of them would not work properly.And of course, I was right. The entire plate is warped and sits up higher on one side than the other.So when installed in the rotor casing, the casing sits lopsided and won't slide onto the shaft properly.So, I grab the other one and look at it. And, of course, it was also warped. But knowing it's just plastic, I knew I could make it work.So I grabbed my heat gun and slowly heated up both sides for about 2 minutes, then used a rubber mallet to conform it to where it sat flush in the case. I bolted it in and it went perfect onto the shaft.BUT.... And this is a big one - if you have an older Kenmore or LG -DO NOT PUT IT ON WITHOUT GETTING THE BIG WASHERS FROM LOWESIt is the HILLMAN # 883570 1-3/8 x 7/8 x 14 ga bushing - It'll be a pack of two in one of their "specialty" drawers.Mine needed both to sit perfect.IF YOU BOLT ON THE ROTOR WITHOUT THE WASHERS, IT WILL POSSIBLY DESTROY YOUR STATOR.YOU HAVE BEEN WARNED.So make sure to push the rotor on first as far as it will go and give it a turn by hand... if it grinds or bumps on anything YOU NEED THE WASHERS
L**E
Almost fits....Dremel fixed it.
Although it looks very much like the OEM part, it is not. Bolt holes and pins lined up on this LG WM0642HW washing machine, but the part would not sit flush. It was about 1/16" of an inch above the face of the rotor. The issue was that the hub protrusion would not sit fully in the recess in the rotor. So I got out my Dremel rotary sander and removed a bit of the lip. Did not have to remove much to get the part to sit flush. After bolting the part on the rotor, I put some light oil on the spline shaft and it went on the drum shaft easily. Works fine.
ترست بايلوت
منذ أسبوعين
منذ شهر
