Self-Leveling Sealant

Great product. Used it for concrete joints for sidewalks and between driveway and garage. Make sure to use good painters tape and pressing the tape firmly in so that the self-leveling doesn't spill over your unintended area of concrete like I did. Also no to put back a rod and underneath the back of rod as necessary put sand so that you don't end up using too much of the sealant. I ended up using all 12 sealants for a three car garage scene and roughly 10 concrete sidewalks that are 4 to 5 ft and width. Very glad I have bought in bulk packaging as I was expecting some leftovers but ended up using all of them. Also make sure to let it dry 24 hours and also for the tape that are used to prevent spillage to remove those tape before the sealant fully cures. I peeled off the tape roughly around 6 to 8 hour of cure. I also test tried it on concrete cracks not sure how this will turn out but at least for now other than the aesthetic side it's a good piece of mind to know cracks are sealed to prevent further erosion beneath the cracks.

This works very well. However, there are some lessons I have learned. I will list them so they might help someone else. 1. Any deep cracks should be filled completely using backer rod or something else; otherwise the product will simply drain into the crack. 2. Wind mixed with leaves is not your friend. The leaves will fall into the product and you will have to wait until it dries to pull out what you can and the ones you can't get out will just have to decompose. 3. Have a piece of cardboard and a rag or paper towels nearby. It can get messy when you finish the section you are working on. The product will not completely stop flowing (slow stringy drip). 4. Start on a spot that is not too conspicuous. The first try will have some mistakes. After 2 or 3 times at using this, you will get really good at it. If you follow my lessons learned you might be good after your first try. Note: it takes about 2 days to dry to the touch. Hope this helps.

This sealant worked exactly as described. It self-levels beautifully on concrete joints and stays flexible after curing. I used it on driveway expansion joints and got a clean, professional-looking finish with no air bubbles. A great go-to product for concrete sealing jobs. Works great with backer rod.

I purchased this product to seal cracks in my 11 YO concrete driveway parking pad and workshop building approach, each having slopes of ~ 3 - 4 degrees. The rest of the long driveway is gravel. I just applied this first tube yesterday, mid-day with the air being relatively dry and the temperature being ~ 83 degrees. My comments are based upon a first time use completing ~ 1/3 of required repairs. I expect to do a much better job with the next two tubes that are on order, based upon this initial experience. This product is very runny. Even using a new caulking gun with a pressure release lever used at the completion of each application, the material still ran out of the tube very profusely. I ended up having to plug the end of the tube quickly after each application stoppage, with the tube being held over a small box to catch all of the material still coming out of the tube- which was a messy affair. It is still tacky and soft after 7 hours. At 24 hours, the material is still slightly soft to finger pressure, but okay to walk on. I will give it another couple days before driving a vehicle on the repairs. - I pressure washed the very dirty concrete to ensure better product adhesion at its outer edges and a better color match. I suspect if I pressure wash again in the future (4000 PSI/, 4 Gal/Min unit) the Sikaflex repair would be damaged. Time will tell. My goal is to stop water entering the cracks and causing more damage. If I have to reapply in say, 5 years, I will do so as required. - I opened the concrete cracks to ~ 1/4" wide and ~ 1/2"+ depth using a grinding disc and would probably do the same next time- to ensure there is enough material applied and any loose concrete was removed. All repair areas were cleaned with a water hose afterwards and left to dry for two days. - Initially I thought I did a good job of filling the cracks completely, as I was moving the caulking gun along the crack. But with the slight compound slopes and possibly NOT filling the crack to the bottom as I thought I was doing- over time as the material was setting up, it sunk/moved to the point I soon went back and applied an additional coat to fill the crack level. In some spots this 2nd coat somehow became kind of "ropey"- see pics. - Next time I will pay better attention to filling the crack to the bottom and not add a second coat, if possible. It may be best to have with a little bit of concave filling rather than the raised "ropey" texture I have in spots that will probably be damaged by vehicle use. Time will tell.

This product is so much better than my highest expectations despite my high regard for Sika products. It is so forgiving to work with and literally gives one so much time to make corrections. The reason being it only skins much later than one would expect. Quite extraordinary.

Just the right sealant I needed, I like the self leveling action. Just make sure you clean the gap/crack then pour it

This stuff was better than I thought it would be! I actually didn't use it for concrete I used it in between two layers of mahogany trim on the hull of a 12 foot fiberglass boat. Outside of the fact it took three days to cure enough to sand it is the exact result I was looking for. There were a couple places where the wood trim was damaged underneath and it leaked down the side of the hull, Where I was able to see it it cleaned up nicely with water and a rag where I didn't see it and it cured It was more difficult to remove I was able to do it with a razor blade. I havent finidhed yet to show the final result / Update The product hardened up nice and was easy to sand (didnt even clog the paper. Only issue the Epoxy Did NOT cover this product It Pooled up and cured in a sporatic patern. I would still buy again... it would be nice if I could figure out why the epoxy would not cover and fix that..

El producto es justo lo que esperaba. Le doy cuatro estrellas debido a que llegó abollado de la parte inferior, pero funcionó correctamente. Ojo con las instrucciones, el tubo no entra en una pistola de silicón convencional, es necesario comprar una más grande.

It got shipped from US to Australia in 2 weeks. Fills in the gap and self levels. It more fluid than expected.