SUNPIE 7 inch Chrome Round Headlight Ring Mounting Bracket Compatible with H_arley Motorcycles Headlight Mount

Product perfectly and works great

Worked great

Item was good, cheap and easy to install

Ordered this to go with a led headlight that did not come with one. It fit nicely until it came time ti install headlight bezel. The screw that they sent to hold on the bezel had to be replaced because it was not long enough. The tab on the bottom that holds the bezel in place was bent to 90 degrees off vertical up. This may be good to work with a sunpie bezel but not a harley bezel. I had to bend the tab up in order to fit the factory bezel along with get a longer screw to make this work. That said, minor issues. Easily remedied. Will buy again if needed. It would be nice if manufacturer would pay closer attention to detail.

I replaced the halogen headlight on my 2000 Road King with an LED bulb. After cutting away the old mount for the LED light to fit in the housing, it would rattle when hitting bumps. I replaced it with this and it fit perfectly, it comes with the mounting screws and a new stainless ring to hold the headlight in place. That was a pleasant surprise as my old ring was getting fairly worn after 23 years. Took about 15 minutes to remove the old one and replace it with this. The metal seems to be thicker and better quality than OEM. I HIGHLY RECOMMEND

Piece of JUNK!!!! The install went on easy, however the gap in the housing for the LED headlights itself was to large in its depth. I had to make a gasket to fill in the area so the light would fit snug and not move (rattle) back and fourth. Now, once it was on the whole in the base for the headlight trim piece was also a little lage as the screw didn't fit as snug as the stock housing. Lastly, they don't put any sort of lock titer on the screws that contain springs for adjustment of the beam.After install was complete and I was riding home, I noticed my headlight seemed to be canted. Well when I reached up to feel, the trim piece was completely gone, so I stopped to find 2 of the 3 screws were completely out with the springs missing, and my light was barely, and I mean barley held in by a few threads on the 3rd screw. This product about cost me a whole lot of money. Either way I have to purchase a new trim piece, and figure out springs for the other two adjusters.Very disappointed.... and quite frustrated......

This item is a good solid unit there's no doubt you're going to need this to correctly and efficiently mount the high-performance headlights. But I must warn you that there are some issues, and things that I would do totally different. For one I would use a drop a Loctite blue on every thread and screw! Surprisingly they can work loose, lose one and you definitely have problems because you just won't find these items in any hardware store. Seem to be a priority item just for these units. The other issue the headlight ring that goes on the outside to seal everything up, on the very bottom normally there is that self-tapping sheet metal screw that's used to fasten this ring down. Simply that just does not work well with that said, I wound up using the tap in a machine screw to take its place. One last thing when you unscrew your old unit from the fairing, by all means, keep track of one whole each screw came out of! When reinstalling use a little soap or beeswax to get that screw back in place. Hope that helps!

This piece is needed for proper installation of Sunpie LED headlamp for Harley. After trying to cut the stock bracket/bowl to fit the headlamp like some of the other reviewers posted on the headlamp, I gave up and ordered this. I did have to straighten part of it a little bit. No big deal because you don't see it anyway. Simple install. Perfect fit. I used this on a 2011 Ultra Limited. My bike already had the larger chrome over sized trim ring, but I think it would probably still look ok without it. I wish I knew up front that I needed this for an easier job putting the headlamp in. I am satisfied with my purchase and would buy it again.

satisfait

I brought the full kit, To fit my 2008 Electra Glide Classic.The kit i got; the 4.5in passing lights, 7in headlight + the headlight ring. No instructions but I did not need them.Perfect fit, the wiring plugged in first time and no modification to anything.Nice and bright. Need to road test now. *** The original finish trim ring did not fit easily but it in they'd i got it

Hochwertige Verarbeitung und ein guter Preis. Markenprodukte können hier nicht mithalten. Würde ich weiter empfehlen. Leider erfolgt der Einbau nach Weihnachten, da es als Geschenk gedacht ist.

Ho una standard 2004 che ho svecchiato con nuovi led. Mancava la ghiera in acciaio. Ricevuta in 3 gg. Grazie Amazon Prime.PERFETTA si adatta senza nessuna modifica Ricevuta oggi e portata al meccanico che stava ultimando il tagliando. Montata in 10 min. Avrei potuto farlo da solo. Consigliata a tutti.

Produit conforme à la description. Il s'adapte parfaitement sur le montage d'origine du phare, l'emplacement des vis de fixation correspond bien. Produit de qualité qui permet le montage des phares LED 7 pouces (sur Harley). Je recommande. Livraison rapide.