Rev-A-Shelf 2-Tier Kitchen Cabinet Pullout Shelf and Drawer Organizer Slide Out Pantry Storage Basket in Multiple Sizes, 12 x 22 In, 5WB2-1222CR-1

I just finished installing these in seven of our kitchen cabinets as icing on the kitchen remodel cake. Really tired of getting down on the floor to pull out the heavy mixer or juicer from the back in the bottom of a dark cabinet.Pros: Nice chrome finish and fairly sturdy. I would have preferred the Rev-A Shelf birch wood units but too expensive for our budget. These are reasonable in comparison. Assembly of the unit is about 10 minutes.Cons: Installation took a couple hours for the first one. Maybe 20-30 minutes for each additional unit. Some things were not obvious. See tips below.Several assembly screws easily snapped off. Glad there were extras.My experience:The units are 1/2" smaller than the cabinet opening. I ordered for an 18"w cabinet opening and the unit is 17.5"w. That allows for clearance for protruding door hinges. The instructions said to mount the unit away from the door hinges (off center in the cabinet) which leaves a 1/2" gap on the hinge side. That side just stands in the air unattached or anchored. Being off center bothered me. I would need to add some kind of blocking to move the units to a centered position.In my case I also ordered the door mounts to convert the doors from hinged to a pull out configuration.That's where my confusion started. The door mount brackets were off center from the doors position directly below the drawer because the units were installed off center. I didn't have enough door frame to mount the door that off center. There are round discs (spacers) included with the door mount bracket kits that will allow you to move the brackets left or right but it looked odd to me.I realized that I could use the round discs (spacers) to center the whole unit by using the spacers in between the unit frame and the door frame on either side. The four spacers provided at the four front anchor points. I had to provide longer screws to make this work. The result was a centered unit in the cabinet opening with a centered door pull. See pictures of the spacer positions.Tips:1. Hand tighten the assembly screws. They snapped easily with a screw gun, even with the drag set low.2: If you are installing the door brackets (separate kit) use the spacers to center your unit in the cabinet opening rather than off center. See pictures3: Install the drawers so that you are sure the brackets that attach to the back of the cabinet are truly parallel and won't bind the drawer slides. Mark the holes, remove the drawers and mount the rear brackets. Then attach the unit to the bottom/base with the four screws provided.4: Mounting the door to the brackets: Attach the brackets to the bottom drawer. Tighten the screws just until the brackets stay in place but can still move if pushed with some force. Apply the the double stick tape to the bracket faces. Pull the drawer slightly so that it just sticks out beyond the cabinet face. Line up the door panel under the drawer face right to left and also the door top down from the bottom of the drawer face. Press firmly in toward the brackets so that the brackets adjust from the pressure and the double stick tape adheres to the door panel.. Carefully open the door/drawer and attach the screws.Note: The instructions said to face the brackets outward. This did not work for our doors so we turned them inward.

When I built my previous home they kitchen was loaded wit pull out shelves. Fast forward to my retirement home and while the kitchen is nice the cabinet storage is basic. I dreamed of pull-outs but custome ones were beyond my reno budget. Thought I would try these. This was #8 of the Rev-A-Shelf brand and the only one that is a single tier. I was afraid would lose too much space in my cabinets because they are not a perfect fit. I have actually gained space. Everything is in the cabinets and easily accessible and I have one cabinet still empty - unheard of for me. They have been easy for me to install and I am not much of a DIY'er. The first one took me a while and resulted in a few bruises from crawling in the cabinet but they are installed, very sturdy and slide smoothly. (One exception. I received one with the soft close brackets and still have not been able to get the basket to work. The shelves work so well that I don't need the soft close) One suggestion. The directions tell you to assemble the unit and place it in the cabinet, them finagle around to get the for screws installed. I am short and could not reach over the basket or through the wires to attach the screws and I do not have fancy tools that make life easier. I removed the basket and screwd in the back two screws. Then replaced the basket and pull it out to do the front two screws. Made life much easier.

This is the perfect size for a small narrow cabinet by the sink. It's strong, heavy duty, good quality and was easy to assemble and install. It makes organizing and using that cabinet so easy when before it was just a pain.

Installation was straightforward. I used these in base cabinets that had the annoying half shelf. After I removed the half shelf I was able to install four of these units in about 2 hours. I did add shelf liner on some so small items would not fall through. It is a great upgrade. They seem very sturdy and according to the information are rated for 100 lbs per shelf.