Enermax Tower Case ECA3280A-BR Black/Red

This case seems pretty well made. I like the removable middle harddrive cage. The ssd cage is just ok, i'd like to see some tool-less instead of playing with tiny screws. I used the metal thumb screws from the ssd cage(mounted from underneath the case) on the back of the case since they are nicer than the plastic ones that are included back there... who is going to notice the ones on the bottom of the unit? They should have had them switched around in the first place. I wish the bottom hdd cage was removable. There is plenty of room for routing wires through the back, which is a huge plus. The rear fan seems pretty decent, but is not branded. The dust filters are pretty much garbage. There are cutouts for better snap-in filters to go under the power supply and on the bottom of the unit, but instead its just sloppy mesh. The front panel also has the cheap mesh filters. I wish enermax and other case sellers would sell nicer filters at extra cost, i don't mind that the case is inexpensive because they cut corners on the filters. I just wish I could bring the filters up to meet the higher quality of the other parts. Enermax also uses these filters on their $200+ enermax fulmo gt full tower, and its really a weak point. Especially because they are hard to clean once the unit has been setup. You have to lift the pc up or tip it over, with this case you could do that, with the fulmo, its ridiculous. The top of the case has a lot of different options for mounting fans and possibly radiators, but whether there is enough depth for both, i don't think so. Its likely the fans will need to be mounted outside the case, which means disassembling the fan connectors to get the wires through the upper grill and down into the case. Nice case though, i really like the style and strong frame.

Good quality w lots of interior room. This is the upper scale of a Mid sized case if you ask me, but that allows for work room & good air flow. Cable management is really nice & the back upper opening others complained about has been made larger. There are very few sharp edges & the hdd fasteners work well enough. I did remove 1 to use screws to hold a 5.25 to 3.5" plastic adapter. I also removed the middle hdd rack and installed the bottom base mounted 2.5" SSD bracket in its place - this worked better for me. I have 2 2.5" SSD's mounted here & 3 large capacity 7200rpm HHD's mounted in the lower rack. The 2 front 140mm fans are quiet and move a good amount of air when at full speed. The rear 120mm fan is a joke & I replaced w a more cfm fan. I also installed a top exh fan - that gives me 2 in & 2 out for good air circulation. Plus I have gigantic CPU, PSU & GPU fans - thats 7 fans in all! My AsRock MOBO has enough fan headers that all fans are connected to it & can be controlled thru BIOS software. I did remove all of the vent screens as they block air flow. The biggest issue is that the MOBO stand offs are too short to allow rear I/O usb ports to be properly used. Luckily I have tons in stock and found enough taller ones to raise my MOBO for better clearance. I still had to notch & bend both my USB 2 & USB 3 I/O areas so they could be used. Wish I could vote 4.5 as all was perfect except for back fan & MOBO fasteners.

This product was not as advertised. It will not hold the cooling system, fans and motherboard.

This case has the ability to be a great case. It has plenty of backside room for better cable management and a great system to relieve heat. However there is a huge flaw with this case. It does not fit a 280mm Radiator with its fans. I bought this product because the description stated that it supported a 280mm radiator on the top. But when I tried to install a Corsair H115i radiator on the top it was an EPIC fail. The radiator did not line up with the screws holes on the top and I had ZERO room to install the fans that attached to the radiator because the motherboard was too close to the radiator to install fans. There is a possibility of making it work by installing in the front, but you would have to completely gut out the hard drive bays and the 5.25 bays, then it might work. I wanted to send it back to the seller but they told me that I was responsible for shipping and there's a 15% restocking fee. With that i'm losing half of what I paid in order to return it. I honestly would not order anything from this seller if this is there return policy.

The product itself is a nice case.HOWEVERThe management of this case was horribleThe plastic strip with holes in them(most likely for cooling) under the case was all wrinkled and messed up because they forced the screws too hard on them. Which shouldn't be the case because those are freaking thumb screws.Also, the back side panel of the case was flushed so hard that it was stuck and I for now can't open it.The case itself is a nice case, so I would suggest people who want to purchase this case buy from a different seller