Auto Ventshade[AVS] Outside Mount Rain Guards For 07-13 Silverado 1500/Avalanche Sierra 1500; 07-14 Silverado/Sierra 2500HD-3500HD Crew/07-14 YukonXL | Window Vent Visors, 4 pcs. - Smoke | 94515

It was the perfect fit for my truck and took only 30 minutes to1 hour to install

so far so good 2 month

Adhesive isn’t that good but I did install in winter so maybe with windows rolled up for a period of time it will stick better. I like weathertech better but way more expensive and their shipping is ridiculously high.

Great for letting the summertime heat out while keeping rain from getting in. I've never tried the in-channel type as this style has always worked well. No additional wind noise noted at highway speeds either. The front ones need no labeling as each will only fit on its respective side. Be sure to note which is RR (right rear) and which is LR (left rear/driver's side) when doing the back windows. They will fit on either side, but I know that following this there was no additional wind noise at speed.Installation tips - after thoroughly cleaning and drying your door frames, test fit each piece. I am 5'10" and my truck sits up a bit so I stand on a 6" platform to get a better perspective. Next, tear off 6 or 7 1.5" to 2" pieces of masking tape and lightly stick one end of each near the bottom of the first window to be done. Again, put the Ventshade in place, making sure the 3M tape, when exposed, will fully contact the door frame around the window. I try to mount mine as low as possible, which allows me to open the window a little bit more and still keep rain out. While still holding the Ventshade in its ideal spot, start placing the strips of masking tape parallel to the piece at key points - at the bottom of each end, along the top curvature and along the straight edge at top. Now you can begin to remove the covering from the double-sided tape and attach the Ventshade, starting at one end and working your way towards the other, gently pulling the red covering off the tape as you go. Using the masking tape as a guide, you can easily put the Ventshade back in exactly the same spot you previously determined. And if you have any question as to how the front and rear visors will line up with each other, use some more masking tape to lightly hold one piece in place while you mark off where the other will go. After all pieces are in place, using a soft cloth and pressing firmly, run your finger along the edge of each piece. This will further seat them and, barring an accident, you can be assured they will stay in place.

Easy install

Fit great easy to install and quite.

I will start off by saying that I bought these to replace my old AVS window guards. Same exact brand also both stick on style. There were minor differences and the hardest part was taking the old glue off from the old AVS Window visors. I didn't know at the time but I'd recommend buying an eraser wheel if you don't wanna spend hours rubbing off old double sided tape. The old ones I have no clue how long they'd been on there but eventually one or two of them had cracked and they all had faded. The new ones, I now have 2 years with, and the tape remains strong, the smoke isn't faded. And luckily no cracks or anything in the visors. I was able to tell they had done a slight redesign to the new ones and have included pictures of both the new and old ones for your viewing pleasure. I hope this review helps someone and if it was up to me I'd always buy the stick on style and definitely would buy these again.

Went right in my 2007 avalanche.. just wish there was adhesive on the small section in the front. You may want to heat a bit before installing so the window clears better when going up...it's the first part it contacts . Try dry fit and put window up and down to check

I watched a short YouTube video before installing these. I was anxious to put them on so I installed them in freezing weather but they still went on easily. No issues at all. Perfect fit and after almost a month there are no issues with them lifting so far. I’m quite happy with them.

Easy install and hold strong

I paid a few extra dollars and purchased the window visor that installs in the window track. This is the superior product over the ones that stick on the surface of the door above the window. The fit on my 2009 Suburban was perfect for all 4 doors. Kit comes with everything you need for the installation. They look great on the car and of course are very functional for their intended purpose. Amazon provides excellent value on this product.

Easy install, fits like it should

I found this simple to install. It is not extremely tight to the doors but low profile enough that it doesn't look clownish. I got the matching vent shade for the hood on my truck too.